Freescale Semiconductor MPC5632M Manual Download Page 996

Page: 996 / 1384

MPC563XM Reference Manual, Rev. 1

996

Freescale Semiconductor

Preliminary—Subject to Change Without Notice

Figure 24-22. EQADC SSI Control Register (EQADC_SSICR)

MDT[0:2] — Minimum Delay after Transmission

MDT field defines the minimum delay after transmission time (t

MDT

) expressed in serial clock (FCK)

periods. t

MDT

is minimum time SDS should be kept negated between two consecutive serial

transmissions.

Table 24-11

lists the minimum delay after transfer time according to how MDT is set.

NOTE:

The MDT field must only be written when the serial transmissions from the EQADC
SSI are disabled - See ESSIE field in

Section 24.5.2.1, “EQADC Module

Configuration Register (EQADC_MCR)

BR[0:3] — Baud Rate Field

The BR field selects system clock divide factor as shown in

Table 24-12

. The baud clock is calculated by

dividing the system clock by the clock divide factor specified with the BR field.

NOTE:

The BR field must only be written when the EQADC SSI is disabled - See ESSIE field
in

Section 24.5.2.1, “EQADC Module Configuration Register (EQADC_MCR)

RESET:

MDT

RESET:

= Unimplemented or Reserved

Table 24-11. Minimum Delay After Transmission (t

MDT

) Time

MDT

(FCK period)

0b000

0b001

0b010

0b011

0b100

0b101

0b110

0b111

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands

Freescale Semiconductor MPC5632M, Manual

Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands