manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

652

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

FLAGCAP — FLAG Capture Event bit

The FLAGCAP Flag indicates that a capture event has occurred, thus triggering a time base capture 
into the T24CAPA register. The very first capture after coming out from Disable to Wheel Speed mode 
is not indicated through FLAGCAP since data within T24CAPA and T24CAPB may be not coherent. 
The FLAGCAP flag is cleared if the Status register is written with the FLAGCAPC bit set. It is cleared 
also if the EMIOSWSCAEC register is accessed for read in Wheel Speed mode out of freeze state (byte 
enables in EMIOSWSCAEC register accesses are ignored for this purpose). If when attempting to 
clear the FLAGCAP flag a new capture event occurs at the same time, then the flag remains set 
indicating that a new time base value was captured into the T24CAPA register. The OVRCAP flag will 
not be set in this case.

1 = Capture event detected
0 = Capture event not detected

FLAGPW — FLAG Pulse Width Capture Event bit

The FLAGPW indicates that a Capture Event occurred in the pulse width detection logic. A capture 
event is defined as an edge in the input signal which had propagated through the channel input filter 
and validated by the edge selection logic. The FLAGPW flag is cleared if the Status register is written 
with the FLAGPWC bit set. It is cleared also if the EMIOSWSPW register is accessed for read in 
Wheel Speed mode out of freeze state (byte enables in EMIOSWSPW register accesses are ignored for 
this purpose). If when attempting to clear the FLAGPW flag a new event occurs at the same time, then 
the flag remains set indicating that a new capture event had occurred.

1 = Capture event detected
0 = Capture event not detected

FLAGECO — FLAG Event Counter Overflow bit

The FLAGECO bit is set when the Event Counter register overflows. The FLAGECO flag is cleared 
if the Status register is written with the FLAGECOC bit set. It is cleared also if the EMIOSWSCAEC 
register is accessed for read in Wheel Speed mode out of freeze state (byte enables in 
EMIOSWSCAEC register accesses are ignored for this purpose). If when attempting to clear the 
FLAGECO flag a new overflow on Event Counter occurs then the flag remains set to indicate it.

1 = FLAGECO set event has occurred
0 = No overflow

FLAGCE — FLAG Compare Event bit

The FLAGCE bit is set when the Event Counter matches the Event Data register triggering a capture 
into the T24CAPEV register. The FLAGCE flag is cleared if the Status register is written with the 
FLAGCEC bit set. It is cleared also if the EMIOSWSEV register is accessed for write in Wheel Speed 
mode out of freeze state (byte enables in EMIOSWSEV register accesses are ignored for this purpose). 
If when attempting to clear the FLAGCE flag a new match occurs between the Event Counter and the 
Event Data register then the flag remains set indicating that a new match had occurred.

1 = FLAGC set event has occurred
0 = No overflow

To see in detail the precedence of events that set and clear flags and overruns go to 

Section 22.5.2.3, 

“Wheel Speed Channel Flags Operation

.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

Hanna Instruments BL120 Instruction Manual preview
BL120
Brand: Hanna Instruments Pages: 54
Hanna Instruments BL 983320-0 Instruction Manual preview
BL 983320-0
Brand: Hanna Instruments Pages: 2
Watlow F4T Installation And Troubleshooting User’S Manual preview
F4T
Brand: Watlow Pages: 59
Watts Tekmar WiFi Snow Melting Control 670 Installation Manual preview
Tekmar WiFi Snow Melting Control 670
Brand: Watts Pages: 48
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Brand: Data Signs Pages: 23
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Brand: ICP DAS USA Pages: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Brand: National Instruments Pages: 22
YASKAWA A1000 HHP Programming Manual preview
A1000 HHP
Brand: YASKAWA Pages: 360
Allen-Bradley CENTERLINE Instruction Manual preview
CENTERLINE
Brand: Allen-Bradley Pages: 88
V2 FORTECO 2500-I Manual preview
FORTECO 2500-I
Brand: V2 Pages: 108
Encelium Wired Manager - DALI Installation Instructions Manual preview
Wired Manager - DALI
Brand: Encelium Pages: 8
Taylor i16 Operating Manual preview
i16
Brand: Taylor Pages: 34
Melexis DVK90121 User Manual preview
DVK90121
Brand: Melexis Pages: 13
SystemAir fantech IPF05-1L Installation Instructions preview
fantech IPF05-1L
Brand: SystemAir Pages: 2
ICP DAS USA ISaGRAF mPAC Series Getting Started preview
ISaGRAF mPAC Series
Brand: ICP DAS USA Pages: 75
Freescale Semiconductor 56F8037 User Manual preview
56F8037
Brand: Freescale Semiconductor Pages: 41
Broan VBATHW Installation And User Manual preview
VBATHW
Brand: Broan Pages: 2
Viking Electronics SLP-1 Installation And Application Manual preview
SLP-1
Brand: Viking Electronics Pages: 12

Brands by name

Popular brands

Load more brands