manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

411

 

Preliminary—Subject to Change Without Notice

Chapter 14  
Interrupt Controller (INTC)

14.1

Information Specific to This Device

This section presents device-specific parameterization and customization information not specifically 
referenced in the remainder of this chapter.

14.1.1

Device-Specific Features

•

191 peripheral interrupt request sources

•

165 reserved positions

•

8 software interrupts

•

4-byte offset between vectors

14.1.2

Device-Specific Register Information

•

53 Priority Select Registers for a total of 364 interrupt vectors

•

112 reserved interrupt vectors

14.2

Introduction

14.2.1

Module Overview

The interrupt controller (INTC) provides priority-based preemptive scheduling of interrupt requests. This 
scheduling scheme is suitable for statically scheduled hard real-time systems. The INTC is optimized for 
a large number of interrupt requests, up to 512. It is targeted to work with a Power Architecture Book E 
processor and automotive powertrain applications where the ISRs nest to multiple levels, but it also can 
be used with other processors and applications.

For high priority interrupt requests in these target applications, the time from the assertion of the interrupt 
request from the peripheral to when the processor is performing useful work to service the interrupt request 
needs to be minimized. The INTC supports this goal by providing a unique vector for each interrupt 
request source. It also provides 16 priorities so that lower priority ISRs do not delay the execution of higher 
priority ISRs. Since each individual application will have different priorities for each source of interrupt 
request, the priority of each interrupt request is configurable.

When multiple tasks share a resource, coherent accesses to that resource need to be supported. The INTC 
supports the Priority Ceiling Protocol for coherent accesses. By providing a modifiable priority mask, the 
priority can be raised temporarily so that all tasks which share the resource can not preempt each other.

Multiple processors can assert interrupt requests to each other through software setable interrupt requests. 
These same software setable interrupt requests also can be used to break the work involved in servicing an 
interrupt request into a high priority portion and a low priority portion. The high priority portion is initiated 
by a peripheral interrupt request, but then the ISR can assert a software setable interrupt request to finish 

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

Vacon 20 Quick Manual preview
20
Brand: Vacon Pages: 62
Particle B Series Quick Start Manual preview
B Series
Brand: Particle Pages: 6
GE RSTi-EP User Manual preview
RSTi-EP
Brand: GE Pages: 425
Faulhaber MC 5004 Technical Manual preview
MC 5004
Brand: Faulhaber Pages: 66
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Brand: RBI Pages: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Brand: RBH Access Technologies Pages: 36
S&C PMH Inspection Manual preview
PMH
Brand: S&C Pages: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Brand: S&C Pages: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Brand: S&C Pages: 19
Dahua DHI-ARC3008C User Manual preview
DHI-ARC3008C
Brand: Dahua Pages: 137
IDTECK Star RFL200 Quick Manual preview
Star RFL200
Brand: IDTECK Pages: 12
Banner XS26-2 Series Manual preview
XS26-2 Series
Brand: Banner Pages: 2
Eaton CGLine+ Web Controller Installation And Operating Instructions Manual preview
CGLine+ Web Controller
Brand: Eaton Pages: 28
Jetter 60873050 Manual preview
60873050
Brand: Jetter Pages: 24
Netafim AlphaDisc BLE Quick Manual preview
AlphaDisc BLE
Brand: Netafim Pages: 4
TREND IQ422 Installation Instructions Manual preview
IQ422
Brand: TREND Pages: 12
Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Brand: Objective Imaging Pages: 11
ZEDAR Regency Owner'S Manual preview
Regency
Brand: ZEDAR Pages: 25

Brands by name

Popular brands

Load more brands