Freescale Semiconductor MPC5632M Manual Download Page 128

Page: 128 / 1384

MPC563XM Reference Manual, Rev. 1

128

Freescale Semiconductor

Preliminary—Subject to Change Without Notice

for the DMACR definition.

Figure 7-2. DMA Control Register (DMACR)

Register address: DMA_ 0x0000

RESET:

GRP3PRI

GRP2PRI

GRP1PRI

GRP0PRI

ERG

ERC

EDB

EBW

RESET:

= Unimplemented

Table 7-3. DMA Control Register (DMACR) Field Descriptions

Name

Description

Value

GRP3PRI

Channel Group 3 Priority

Group 3 priority level when fixed priority group

arbitration is enabled.

GRP2PRI

Channel Group 2 Priority

Group 2 priority level when fixed priority group

arbitration is enabled.

GRP1PRI

Channel Group 1 Priority

Group 1 priority level when fixed priority group

arbitration is enabled.

GRP0PRI

Channel Group 0 Priority

Group 0 priority level when fixed priority group

arbitration is enabled.

ERGA

Enable Round Robin Group Arbitration

0 Fixed priority arbitration is used for selection

among the groups.

1 Round robin arbitration is used for selection

among the groups.

ERCA

Enable Round Robin Channel Arbitration

0 Fixed priority arbitration is used for channel

selection within each group.

1 Round robin arbitration is used for channel

selection within each group.

EDBG

Enable Debug

0 The assertion of the ipg_debug input is ignored.

1 The assertion of the ipg_debug input causes the

DMA to stall the start of a new channel.

Executing channels are allowed to complete.

Channel execution will resume when

either the ipg_debug input is negated or the

EDBG bit is cleared.

EBW

Enable Buffered Writes

0 The bufferable write signal (hprot[2]) is not

asserted during AMBA AHB writes.

1 The bufferable write signal (hprot[2]) is asserted

on all AMBA AHB writes except for the last

write sequence.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands

Freescale Semiconductor MPC5632M, Manual

Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands