manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 659

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

659

 

Preliminary—Subject to Change Without Notice

Figure 22-24. Unified Channel Control and Datapath Block Diagrams

22.5.1.1

UC Modes of Operation

The mode of operation of the Unified Channel is determined by the mode select bits MODE[0:6] in the 
EMIOSC[n] register (see 

Table 22-15

 for details).

When entering an output mode (except for GPIO mode), the output flip-flop is set to disabled state 
according to ODIS bit in the EMIOSC[n] register.

As the internal counter EMIOSCNT[n] continues to run in all modes (except for GPIO mode), it is possible 
to use this as a time base if the resource is not used in the current mode.

A2

B2

B1

A1

CNT

local counter bus 

global counter bus[A]

A Comparator

BSL[0]

BSL[1]+logic

BSL[1]+logic

BSL[1]+logic

internal counter

[B/C/D/E]

B Comparator

uc_datapath

uc_ctrl

con

trol sign

al

s

input
filter

input

mode 0

logic

General

Purpose

Registers

mode 1

logic

mode n

logic

MODE

decoder

MODE

register

==

==

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands