manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 989

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

989

 

Preliminary—Subject to Change Without Notice

0 = CFIFO in single-scan level- or edge-trigger mode will ignore trigger events, or CFIFO in 

single-scan software-trigger mode is not triggered.

CFFFx — CFIFO Fill Flag x

CFFFx

 

is set when the CFIFOx is not full. When CFFE

x

 in 

Section 24.5.2.8, “EQADC Interrupt and 

DMA Control Registers (EQADC_IDCR)

 and CFFFx are both asserted, an interrupt or a DMA request 

will be generated depending on the status of the CFFSx bit. When CFFSx is negated (interrupt requests 
selected), software clears CFFFx by writing a “1” to it. Writing a “0” has no effect. When CFFSx is 
asserted (DMA requests selected), CFFFx is automatically cleared by the EQADC when the CFIFO 
becomes full.

1 = CFIFOx is not full.
0 = CFIFOx is full.

NOTE:

Writing “1” to CFFFx when CFFSx is asserted (DMA requests selected) is not 
allowed.

NOTE:

When generation of interrupt requests is selected (CFFSx=0), CFFFx must only be 
cleared in the ISR after the CFIFOx push register is accessed.

RFOFx — RFIFO Overflow Flag x

RFOFx indicates an overflow event on RFIFOx. RFOF

x

 is set when RFIFOx is already full, and a new 

data is received from the on-chip ADCs or from the external device. The RFIFOx will not overwrite 
older data in the RFIFO, and the new data will be ignored. When RFOIEx in 

Section 24.5.2.8, 

“EQADC Interrupt and DMA Control Registers (EQADC_IDCR)

 and RFOFx are both asserted, the 

EQADC generates an interrupt request.

Apart from generating an independent interrupt request for an RFIFOx overflow event, the EQADC 
also provides a combined interrupt at which the Result FIFO Overflow Interrupt, the Command FIFO 
Underflow Interrupt, and the Command FIFO Trigger Overrun Interrupt requests of ALL CFIFOs are 
ORed. When RFOIEx, CFUIEx, and TORIEx are all asserted, this combined interrupt request is 
asserted whenever one of the following 18 flags becomes asserted: RFOFx, CFUFx, and TORFx 
(assuming that all interrupts are enabled). See 

Section 24.6.8, “EQADC DMA/Interrupt Request

 for 

details.

Write “1” to clear RFOFx. Writing a “0” has no effect.

1 = An RFIFO overflow event occurred.
0 = No RFIFO overflow event occurred.

RFDF

x

 — RFIFO Drain Flag x

RFDFx indicates if RFIFOx has valid entries or not. RFDFx

 

is set when the RFIFOx has at least one 

valid entry in it. When RFDEx in 

Section 24.5.2.8, “EQADC Interrupt and DMA Control Registers 

(EQADC_IDCR)

 and RFDFx are both asserted, an interrupt or a DMA request will be generated 

depending on the status of the RFDSx bit. When RFDSx is negated (interrupt requests selected), 
software clears RFDFx by writing a “1” to it. Writing a “0” has no effect. When RFDSx is asserted 
(DMA requests selected), RFDFx is automatically cleared by the EQADC when the RFIFO becomes 
empty.

1 = RFIFOx has at least one valid entry.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands