manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 412

MPC563XM Reference Manual, Rev. 1

412

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

the servicing in a lower priority ISR. Therefore these software setable interrupt requests can be used 
instead of the peripheral ISR scheduling a task through the RTOS.

14.2.2

Block Diagram

Figure 14-1

 is a block diagram of the dual-core INTC. In this document, any features described for 

Processor 0 are intended to be backward compatible with the single core interrupt controller used on the 
eSYS family of devices.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands