manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

546

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

16.9.21 Chip Configuration Register (SIU_CCR)

Figure 16-106. Chip Configuration Register (SIU_CCR)

MATCH — Compare Register Match

The MATCH bit is a read only bit that holds the value of the match input signal to the SIU. The match 
input is asserted if the values in the SIU_CMPAH/SIU_CMPAL and SIU_CMPBH/SIU_CMPBL are 
equal.

1 = Match input signal is asserted
0 = Match input signal is negated

DISNEX — Disable Nexus

The DISNEX bit is a read only bit that holds the value of the Nexus disable input signal to the SIU. 
When system reset negates, the value in this bit depends on the censorship control word and the boot 
configuration bits.

1 = Nexus disable input signal is asserted
0 = Nexus disable input signal is negated

CRSE — Calibration Reflection Suppression Enable

The CRSE bit enables the suppression of reflections from the EBI’s calibration bus onto the 
non-calibration bus. The EBI drives some outputs to both the calibration and non-calibration busses. 
When CRSE is asserted, the values driven onto the calibration bus pins will not be reflected onto the 
non-calibration bus pins. When CRSE is negated, the values driven onto the calibration bus pins will 

Table 16-48. ADC Queue Trigger x eTPU Channel

Field

eTPU Channel

eTSEL1

7

eTSEL2

14

eTSEL3

22

eTSEL4

30

SI 0x980

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

0

0

0

0

0

0

0

0

0

MAT

CH

DIS-
NEX

W

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

U

1

1

During reset the comparison is performed and result is uncertain

U

2

2

The value after reset is uncertain

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

0

0

0

0

0

0

0

0

0

0

0

0

CRS

E

0

W

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

= Unimplemented or Reserved

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

Partizan PAB-FC2 Quick Start Manual preview
PAB-FC2
Brand: Partizan Pages: 7
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Brand: MacroAir Technologies Pages: 32
Oriental motor ASD10A-K Operating Manual preview
ASD10A-K
Brand: Oriental motor Pages: 52
Opt OPT-DPA1024E-4 Manual preview
OPT-DPA1024E-4
Brand: Opt Pages: 40
Beckhoff CX8080 Documentation preview
CX8080
Brand: Beckhoff Pages: 67
Omron K8AK-LS Manual preview
K8AK-LS
Brand: Omron Pages: 12
Progeny Crystal.PoE V4 Manual preview
Crystal.PoE V4
Brand: Progeny Pages: 4
VDH ALFANET 1-LS User Manual preview
ALFANET 1-LS
Brand: VDH Pages: 4
VIRDI AC-2200 User Manual preview
AC-2200
Brand: VIRDI Pages: 73
Ayra 9000-0043-8700 User Manual preview
9000-0043-8700
Brand: Ayra Pages: 19
Aerotech ABL9000 Series User Manual preview
ABL9000 Series
Brand: Aerotech Pages: 36
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Brand: DPS Telecom Pages: 82
Wahlberg 255.700 User Manual preview
255.700
Brand: Wahlberg Pages: 40
Danfoss EKC 531D1 Instructions Manual preview
EKC 531D1
Brand: Danfoss Pages: 18
Zapi SEM-Zero Manual preview
SEM-Zero
Brand: Zapi Pages: 39
Astrapool LumiPlus Quick Start Manual preview
LumiPlus
Brand: Astrapool Pages: 2
3M Touch Screen Controller RX151 Reference Manual preview
Touch Screen Controller RX151
Brand: 3M Pages: 31
Delta Electronics Programmable Logic Controller DVP28SV Instruction Sheet preview
Programmable Logic Controller DVP28SV
Brand: Delta Electronics Pages: 2

Brands by name

Popular brands

Load more brands