Freescale Semiconductor MPC5632M Manual Download Page 34

Page: 34 / 1384

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

Preliminary—Subject to Change Without Notice

— eSCI bit rate up to 1 Mbps

— Advanced error detection, and optional parity generation and detection

— Word length programmable as 8, 9, 12 or 13 bits

— Separately enabled transmitter and receiver

— LIN support

— DMA support

— Interrupt request support

— Programmable clock source: system clock or oscillator clock

— Support Microsecond Bus (Timed Serial Bus - TSB) uplink Version 1.0

•

2 FlexCAN

— One with 32 message buffers; the second with 64 message buffers

— Full implementation of the CAN protocol specification, Version 2.0B

— Based on and including all existing features of the Freescale TouCAN module

— Programmable acceptance filters

— Short latency time for high priority transmit messages

— Arbitration scheme according to message ID or message buffer number

— Listen only mode capabilities

— Programmable clock source: system clock or oscillator clock

— Message buffers may be configured as mailboxes or as FIFO

•

Nexus port controller (NPC)

— Per IEEE-ISTO 5001-2003

— Real time development support for PowerPC core and eTPU Plus engine through Nexus class

2/1

— Read and write access (Nexus class 3 feature that is supported on this device)

– Run-time access of entire memory map

– Calibration

— Support for data value breakpoints / watchpoints

– Run-time access of entire memory map

– Calibration

Table constants calibrated using MMU and internal and external RAM

Scalar constants calibrated using cache line locking

— Configured via the IEEE 1149.1 (JTAG) port

•

IEEE 1149.1 JTAG controller (JTAGC)

— IEEE 1149.1-2001 Test Access Port (TAP) interface

— A 5-bit instruction register that supports IEEE 1149.1-2001 defined instructions

— A 5-bit instruction register that supports additional public instructions

— 3 test data registers: a bypass register, a boundary scan register, and a device identification

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands

Freescale Semiconductor MPC5632M, Manual

Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands