manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 1280

MPC563XM Reference Manual, Rev. 1

1280

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

1 = FIFO enabled
0 = FIFO not enabled

HALT — Halt FlexCAN

Assertion of this bit puts the FlexCAN module into Freeze Mode. The CPU should clear it after 
initializing the Message Buffers and Control Register. No reception or transmission is performed by 
FlexCAN before this bit is cleared. While in Freeze Mode, the CPU has write access to the Error 
Counter Register, that is otherwise read-only. Freeze Mode can not be entered while FlexCAN is in 
any of the low power modes. See 

Section 28.5.9.1, “Freeze Mode,”

 for more information.

1 = Enters Freeze Mode if the FRZ bit is asserted.
0 = No Freeze Mode request.

NOT_RDY — FlexCAN Not Ready

This read-only bit indicates that FlexCAN is either in Disable Mode, Doze Mode, Stop Mode or Freeze 
Mode. It is negated once FlexCAN has exited these modes.

1 = FlexCAN module is either in Disable Mode, Doze Mode, Stop Mode or Freeze Mode
0 = FlexCAN module is either in Normal Mode, Listen-Only Mode or Loop-Back Mode

WAK_MSK — Wake Up Interrupt Mask

This bit enables the Wake Up Interrupt generation.

1 = Wake Up Interrupt is enabled
0 = Wake Up Interrupt is disabled

SOFT_RST — Soft Reset

When this bit is asserted, FlexCAN resets its internal state machines and some of the memory mapped 
registers. The following registers are reset: MCR (except the MDIS bit), TIMER, ECR, ESR, 
IMASK1, IMASK2, IFLAG1, IFLAG2. Configuration registers that control the interface to the CAN 
bus are not affected by soft reset. The following registers are unaffected: 
•

CTRL 

•

RXIMR0–RXIMR63

•

RXGMASK, RX14MASK, RX15MASK

•

all Message Buffers

The SOFT_RST bit can be asserted directly by the CPU when it writes to the MCR Register, but it is 
also asserted when global soft reset is requested at MCU level. Since soft reset is synchronous and has 
to follow a request/acknowledge procedure across clock domains, it may take some time to fully 
propagate its effect. The SOFT_RST bit remains asserted while reset is pending, and is automatically 
negated when reset completes. Therefore, software can poll this bit to know when the soft reset has 
completed. 

Soft reset cannot be applied while clocks are shut down in any of the low power modes. The module 
should be first removed from low power mode, and then soft reset can be applied.

1 = Resets the registers marked as “affected by soft reset” in 

Table 28-2

0 = No reset request

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands