manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

987

 

Preliminary—Subject to Change Without Notice

Write “1” to clear the TORF

x

 bit. Writing a “0” has no effect.

1 = Trigger overrun occurred.
0 = No trigger overrun occurred.

NOTE:

The trigger overrun flag will not set for CFIFOs configured for software trigger 
mode.

PFx — Pause Flag x

PF behavior changes according to the CFIFO trigger mode. In edge trigger mode, PFx is set when the 
EQADC completes the transfer of an entry with an asserted Pause bit from CFIFOx. In level trigger 
mode, when CFIFOx is in TRIGGERED status, PFx is set when CFIFO status changes from 
TRIGGERED due to the detection of a closed gate. An interrupt routine, generated due to the asserted 
PF, can be used to verify if a complete scan of the CQueue was performed. If a closed gate is detected 
while no command transfers are taking place, it will have immediate effect on the CFIFO status. If a 
closed gate is detected while a command transfer to an on-chip CBuffer is taking place, it will only 
affect the CFIFO status when the transfer completes. If a closed gate is detected during the serial 
transmission of a command to the external device, it will have no effect on the CFIFO status until the 
transmission completes. The transfer of entries bound for the on-chip ADCs is considered completed 
when they are stored in the appropriate CBuffer. The transfer of entries bound for the external device 
is considered completed when the serial transmission of the entry is completed. In software trigger 
mode, PFx will never become asserted.

If PIE

x

 in 

Section 24.5.2.8, “EQADC Interrupt and DMA Control Registers (EQADC_IDCR)

 and PFx 

are asserted, an interrupt will be generated. Write “1” to clear the PF

x

. Writing a “0” has no effect. 

Refer to 

Section 24.6.4.7.3, “Pause Status

 for more information on the Pause Flag.

1 = Entry with asserted PAUSE bit was transferred from CFIFOx (CFIFO in edge trigger mode), or 

CFIFO status changes from TRIGGERED due to detection of a closed gate (CFIFO in level 
trigger mode).

0 = Entry with asserted PAUSE bit was not transferred from CFIFOx (CFIFO in edge trigger mode), 

or CFIFO status did not change from TRIGGERED due to detection of a closed gate (CFIFO 
in level trigger mode).

NOTE:

In edge trigger mode, an asserted PFx only implies that the EQADC has finished 
transferring a command with an asserted PAUSE bit from CFIFOx. It does not 
imply that result data for the current command and for all previously transferred 
commands has been returned to the appropriate RFIFO.

NOTE:

In software or level trigger mode, when the EQADC completes the transfer of an 
entry from CFIFOx with an asserted PAUSE bit, PFx will not be set and transfer of 
commands will continue without pausing.

EOQFx — End of Queue Flag x

EOQFx indicates that an entry with an asserted EOQ bit was transferred from CFIFOx to the on-chip 
ADCs or to the external device - see 

Section 24.6.2.3, “Message Format in EQADC

 for details about 

command message formats. When the EQADC completes the transfer of an entry with an asserted 
EOQ bit from CFIFOx, EOQFx

 

will be set. The transfer of entries bound for the on-chip ADCs is 

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

IBM 1L Maintenance Information preview
1L
Brand: IBM Pages: 20
Eaton S611 User Manual preview
S611
Brand: Eaton Pages: 96
Parker 890CS Product Manual preview
890CS
Brand: Parker Pages: 478
Shimaden PAC18A Series Instruction Manual preview
PAC18A Series
Brand: Shimaden Pages: 32
Infineon XE166 Series Hardware Manual preview
XE166 Series
Brand: Infineon Pages: 28
Harmonic Drive RSF-B mini Series Manual preview
RSF-B mini Series
Brand: Harmonic Drive Pages: 32
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Brand: Topcon Pages: 9
V2 WES-ADI Instruction Manual preview
WES-ADI
Brand: V2 Pages: 60
ENGGA EVC800i Installation & Adjustment Manual preview
EVC800i
Brand: ENGGA Pages: 8
CLS LDV-45 Manual preview
LDV-45
Brand: CLS Pages: 6
ZPA Pecky, a.s. MODACT MTNED 15 Mounting Instructions preview
MODACT MTNED 15
Brand: ZPA Pecky, a.s. Pages: 48
XINGDASHINE LBP-024 Manual preview
LBP-024
Brand: XINGDASHINE Pages: 3
Wachendorff OPUS A6 ECO 2 Operating Manual preview
OPUS A6 ECO 2
Brand: Wachendorff Pages: 35
Electrosmith 3340 VCO Build Manual preview
3340 VCO
Brand: Electrosmith Pages: 32
digitalview 417100041-3 Instructions Manual preview
417100041-3
Brand: digitalview Pages: 30
Rexroth Indramat DURADRIVE SYSTEM200 Project Planning Manual preview
DURADRIVE SYSTEM200
Brand: Rexroth Indramat Pages: 86
Cooper WaveLinx Wired ILM-SCMA0401-2 Installation Instructions Manual preview
WaveLinx Wired ILM-SCMA0401-2
Brand: Cooper Pages: 21
Atkinson Electronics SUNEXPLORER III Series Manual preview
SUNEXPLORER III Series
Brand: Atkinson Electronics Pages: 22

Brands by name

Popular brands

Load more brands