manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

249

 

Preliminary—Subject to Change Without Notice

Table 11-4. CFLASH_MCR Field Descriptions

Field

Description

0

EDC

ECC Data Correction (Read/Clear)
EDC provides information on previous reads. If a ECC Single Error detection and correction occurred, the 
EDC bit will be set to 1. This bit must then be cleared, or a reset must occur before this bit will return to a 0 
state. This bit may not be set to 1 by the User.
In the event of a ECC Double Error detection, this bit will not be set.
If EDC is not set, or remains 0, this indicates that all previous reads (from the last reset, or clearing of EDC) 
were not corrected through ECC.
Since this bit is an error flag, it must be cleared to 0 by writing 1 to the register location. A write of 0 will have 
no effect.
The function of this bit is SoC dependent and it can be configured to be disabled.
0: Reads are occurring normally.
1: An ECC Single Error occurred and was corrected during a previous read.

1–3

Reserved

4–7

SIZE[0:3]

Array space size
Dependent upon the size of the Flash module. SIZE is read only.
0101 Total array size is 1.5 MB

8

Reserved

9–11

LAS[0:2]

Low address space
Corresponds to the configuration of the low address space. All possible values of LAS and the configuration 
to which each value corresponds are shown below. LAS is read only.
010 The LAS value of 010 provides 2 x 16 KB + 2 x 32 KB + 2 x 16 KB + 2 x 64 KB blocks.

12–14

Reserved.

15

MAS

Mid address space size
Corresponds to the configuration of the mid address space. MAS is read only.
0 Two 128-KB blocks are available

16

EER

ECC event error
Provides information on previous reads; if a double bit detection occurred, the EER bit is set to 1.  This bit 
must then be cleared, or a reset must occur before this bit returns to a 0 state. This bit cannot be set by the 
application. In the event of a single bit detection and correction, this bit is not set. If EER is not set, or remains 
0, this indicates that all previous reads (from the last reset, or clearing of EER) were correct.   Since this bit 
is an error flag, it must be cleared to a 0 by writing a 1 to the register location. A write of 0 has no effect.
0 Reads are occurring normally.
1 An ECC Error occurred during a previous read.

Note:

This bit can be set on speculative prefetches that cause double bit error detection. Therefore, use the 
ECSM[FNCE] flag for detecting non-correctable ECC errors in the Flash instead of using 
CFLASH_MCR[EER].

17

RWE

Read-while-write event error
Provides information on previous RWW reads. If a read-while-write error occurs, this bit is set to 1. This bit 
must then be cleared, or a reset must occur before this bit returns to a 0 state. This bit cannot be set to 1 by 
the application. If RWE is not set, or remains 0, this indicates that all previous RWW reads (from the last reset, 
or clearing of RWE) were correct. Since this bit is an error flag, it must be cleared to a 0 by writing a 1 to the 
register location. A write of 0 has no effect.
0 Reads are occurring normally.
1 A read-while-write error occurred during a previous read.

18–19

Reserved

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

FrSky Taranis Q X7S Manual preview
Taranis Q X7S
Brand: FrSky Pages: 2
Salda TPC User Manual preview
TPC
Brand: Salda Pages: 16
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Brand: Lattice Semiconductor Pages: 2
U-Prox IP500 Installation And Programming Manual preview
IP500
Brand: U-Prox Pages: 25
Balboa VL260 Quick Reference Manual preview
VL260
Brand: Balboa Pages: 2
CalAmp LMU 2630MB Installation Manual preview
LMU 2630MB
Brand: CalAmp Pages: 13
Renogy Rover 100A Manual preview
Rover 100A
Brand: Renogy Pages: 36
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Brand: Woodward Pages: 32
Zonex DIGI3U Installation Manual preview
DIGI3U
Brand: Zonex Pages: 16
Allen-Bradley Kinetix 350 User Manual preview
Kinetix 350
Brand: Allen-Bradley Pages: 162
PXM Driver LED 1x2A/48V Manual preview
Driver LED 1x2A/48V
Brand: PXM Pages: 11
Velleman VDP100TT Manual preview
VDP100TT
Brand: Velleman Pages: 11
Allen-Bradley Bulletin 505 Quick Start Manual preview
Bulletin 505
Brand: Allen-Bradley Pages: 7
3M Touch Screen Controller RX151 Reference Manual preview
Touch Screen Controller RX151
Brand: 3M Pages: 31
Delta Electronics Programmable Logic Controller DVP28SV Instruction Sheet preview
Programmable Logic Controller DVP28SV
Brand: Delta Electronics Pages: 2
London Electronics INTUITIVE-I Manual preview
INTUITIVE-I
Brand: London Electronics Pages: 23
Veris Industries TWS Series Installation Manual preview
TWS Series
Brand: Veris Industries Pages: 4
Martin Audio Blackline M3+ Specifications preview
Blackline M3+
Brand: Martin Audio Pages: 1

Brands by name

Popular brands

Load more brands