manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

637

 

Preliminary—Subject to Change Without Notice

The EMIOSCNT[n] register contains the value of the internal counter. When GPIO mode is selected or 
the channel is frozen, the EMIOSCNT[n] register is read/write. For all others modes, the EMIOSCNT[n] 
is a read-only register. When entering some operation modes, this register is automatically cleared (refer 
to 

Section 22.5.1.1, “UC Modes of Operation,”

 for details).

Depending on the channel configuration it may have EMIOSCNT register or not. EMIOSCNT register is 
required for the following modes: OPWFM, OPWFMB, OPWMC, OPWMCB, MC, MCB, PEA, PEC, 
WPTA, QDEC. It means that if no mode requiring EMIOSCNT register is implemented then the register 
can be removed during synthesis through proper parameterization.

It is possible that, for particular reasons, EMIOSCNT be available in one device even if the respective 
channel does not feature any mode that requires it. In this case EMIOSCNT availability should be 
explicitly described in the device SoC Guide.

22.4.2.8

eMIOS200 UC Control Register (EMIOSC[n]) 

EMIOSC[n] address: UC[n] base a $0C

Figure 22-9. eMIOS200 UC Control Register (EMIOSC[n]) 

The Control register gathers bits reflecting the status of the UC input/output signals and the overflow 
condition of the internal counter, as well as several read/write control bits.

FREN — Freeze Enable bit 

The FREN bit, if set and validated by FRZ bit in EMIOSMCR register allows the channel to enter 
freeze state, freezing all registers values when in debug mode and allowing the MCU to perform debug 
functions.

1 = Freeze UC registers values
0 = Normal operation

ODIS — Output Disable bit

The ODIS bit allows disabling the output pin when running any of the output modes with the exception 
of GPIO mode.

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

FRE

N

ODIS ODISSL[0:1

]

UCPRE[0:1

]

UCP
REN

DMA

0

IF[0:3]

FCK

FEN

0

W

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

0

0

0

BSL[0:1]

EDS

EL

EDP

OL

MODE[0:6]

W

FOR

CMA

FOR

CMB

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

= Unimplemented or reserved

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

EasyIO FG Series User Manual preview
FG Series
Brand: EasyIO Pages: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Brand: RMG Pages: 6
National Instruments PXI-8231 Installation Manual preview
PXI-8231
Brand: National Instruments Pages: 6
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Brand: RBI Pages: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Brand: RBH Access Technologies Pages: 36
S&C PMH Inspection Manual preview
PMH
Brand: S&C Pages: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Brand: S&C Pages: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Brand: S&C Pages: 19
Nemesis OSCA-I8 User Manual preview
OSCA-I8
Brand: Nemesis Pages: 6
SOMFY Situo 1 RTS Quick Installation Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 56
Texas Instruments MSP430F67661 Manual preview
MSP430F67661
Brand: Texas Instruments Pages: 27
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
Sonos Controller CR100 Quick Setup Instructions Manual preview
Controller CR100
Brand: Sonos Pages: 12
Eaton DCF 800 TWIN Installation And Maintenance preview
DCF 800 TWIN
Brand: Eaton Pages: 2
Danfoss ECL Comfort 300 User Manual preview
ECL Comfort 300
Brand: Danfoss Pages: 75
GCE Druva MTLX Instructions For Use Manual preview
Druva MTLX
Brand: GCE Pages: 46
Tusa RS-790 Owner'S Manual preview
RS-790
Brand: Tusa Pages: 72
Danfoss 080Z0130 Manual preview
080Z0130
Brand: Danfoss Pages: 96

Brands by name

Popular brands

Load more brands