manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 480

MPC563XM Reference Manual, Rev. 1

480

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

1 = A Software System Reset has occurred.
0 = No Software System Reset has occurred.

SERF — Software External Reset Flag

1 = A Software External Reset has occurred.
0 = No Software External Reset has occurred.

WKPCFG — Weak Pull Configuration Pin Status

1 = WKPCFG pin latched during the last reset was logical one and weak pull up is the default 

setting.

0 = WKPCFG pin latched during the last reset was logical zero and weak pull down is the default 

setting.

ABR — Auto Baud Rate

1 = Auto Baud Rate Enabled.
0 = Auto Baud Rate Disabled, eSys compatible.

BOOTCFG[0-1] — Reset Configuration Pin Status

The BOOTCFG field holds the value of the BOOTCFG[1] pin that was latched on the last negation of 
the RSTOUT pin. The BOOTCFG field is used by the BAM program to determine the location of the 
Reset Configuration Word. See 

Table 4-2

 for a translation of the Reset Configuration Half Word 

location from the BOOTCFG field value.

RGF — RESET Glitch Flag

This bit is set by the MCU when the RESET pin is asserted for more than 2 clocks clock cycles, but 
less than the minimum RESET assertion time of 10 consecutive clocks to cause a reset. This bit is 
cleared by the reset controller for a valid assertion of the RESET pin or a power-on reset or a write of 
one to the bit.

1 = A glitch was detected on the RESET pin.
0 = No glitch was detected on the RESET pin.

16.9.4

System Reset Control Register (SIU_SRCR)

The System Reset Control Register (SIU_SRCR) allows software to generate either a Software System 
Reset or Software External Reset. The Software System Reset causes an internal reset sequence, while the 
Software External Reset only causes the external RSTOUT pin to be asserted for the predetermined 
number of clock cycles (refer to 

Section 4.3.2, “RSTOUT

”). When written to one, the SER bit 

automatically clears after the clock count expires. If the value of the SER bit is one and a zero is written 
to the bit, the bit is cleared and the RSTOUT pin is negated regardless if the clock count has expired

The CRE bit in the SIU_SRCR allows software to enable a Checkstop Reset. If enabled, a Checkstop Reset 
will occur if the checkstop reset input to the reset controller is asserted. The Checkstop Reset is enabled 
by default.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands