Suzuki GA413 Скачать руководство пользователя страница 802

Страница: 802 / 1246

6-26

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

Condition

Possible Cause

Reference Item

Engine hesitates

(Momentary lack of

re-

sponse as the accelera-

tor is depressed.

Can occur at

all vehicle

speeds.

Usually most severe

when first trying to make

the vehicle move, as

from a

stop sign.)

Ignition system out of order

Faulty ignition coil or high-tension cords

Engine overheating

Engine and emission control system out

of order.

Fuel pressure out of specification

Faulty injector

Faulty TP sensor, ECT sensor or MAP

sensor

Faulty ECM

Malfunctioning EGR valve (if equipped)

Low compression

Diagnosis in Section 6F.

Refer to “Overheating” of this table.

Diagnostic Flow Table B-3

Diagnostic Flow Table B-1

TP sensor, ECT sensor or MAP sensor

in Section 6E.

Inspection of ECM and its circuit in Sec-

tion 6E.

EGR system in Section 6E.

Previously outlined.

Surges

(Engine power variation

under steady throttle or

cruise.

Feels like the vehicle

speeds up and down

with no change in the

accelerator pedal.)

Ignition system out of order

Faulty ignition coil or high-tension cord

Engine and emission control system out

of order.

Variable fuel pressure

Faulty MAP sensor (if equipped)

Faulty injector

Faulty ECM

Malfunctioning EGR valve (if equipped)

Diagnosis in Section 6F.

Diagnostic Flow Table B-3

MAP sensor in Section 6E.

Diagnostic Flow Table B-1

Inspection of ECM and its circuit in

Section 6E.

EGR system in Section 6E.

Excessive detonation

(The engine makes

sharp metallic knocks

that change with throttle

opening.

Sounds like pop corn

popping.)

Engine overheating

Ignition system out of order.

Faulty spark plug

Engine and emission control system out

of order.

Clogged fuel filter and fuel lines

Malfunctioning EGR valve (if equipped)

Refer to “Overheating” of this table.

Spark plugs in Section 6F.

Diagnostic Flow Table B-3

EGR system in Section 6E

Malfunctioning EGR valve (if equi

ed)

Poor performance of ECT sensor or MAP

sensor

Faulty injector

Faulty ECM

Others

Excessive combustion chamber deposits

EGR system in Section 6E.

ECT sensor or MAP sensor in Section

6E.

Diagnostic Flow Table B-1

Inspection of ECM and its circuit in

Section 6E.

Piston and cylinder head in Section 6A.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды

Suzuki GA413, Руководство по обслуживанию

Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды