Suzuki GA413 Скачать руководство пользователя страница 303

Страница: 303 / 1246

ENGINE

6-11

Condition

Possible Cause

Reference Item

Engine hesitates

(Momentary lack of

response as the

accelerator is

depressed.

Can occur at

all vehicle

speeds.

Usually most severe

when first trying to make

the vehicle move, as

from a

stop sign.)

Ignition system out of order.

Faulty ignition coil or high-tension cords

Engine overheating

Engine and emission control system out

of order.

Fuel pressure out of specification

Faulty EGR system (if equipped)

Faulty injector

Faulty TP sensor, ECT sensor or MAP

sensor

Faulty ECM .

Low compression

Diagnosis in Section 6F.

Refer to “Overheating” of this table.

Diag. Flow Table B-3 in Section 6E.

Diag. Flow Table B-6 in Section 6E.

Fuel injector injection volume inspec-

tion in Section 6E.

TP sensor, ECT sensor or MAP

sensor in Section 6E.

Inspection of ECM and its circuit

in Section 6E.

Previously outlined.

Surges

(Engine power variation

under steady throttle or

cruise.

Feels like the vehicle

speeds up and down

with no change in the

accelerator pedal.)

Ignition system out of order.

Faulty ignition coil or high-tension cord

Engine and emission control system out

of order.

Variable fuel pressure

Faulty EGR system (if equipped)

Faulty MAP sensor

Faulty injector

Faulty ECM

Diagnosis in Section 6F.

Diag. Flow Table B-3 in Section 6E.

Diag. Flow Table B-6 in Section 6E.

MAP sensor in Section 6E.

Fuel injector injection volume inspec-

tion in Section 6E.

Inspection of ECM and its circuit in

Section 6E.

Excessive detonation
(The engine makes
sharp metallic knocks
that change with throttle
opening.
Sounds like pop corn
popping.)

Engine overheating

Ignition system out of order.

Improper ignition timing

Engine and emission control system
out of order.

Clogged fuel filter and fuel lines

Faulty EGR system (if equipped)

Faulty ECT sensor or MAP sensor

Refer to “Overheating” of this table.

Ignition timing in Section 6F.

Fuel pressure check in Section 6E.
Diag. Flow Table B-6 in Section 6E.
ECT sensor or MAP sensor in

Faulty ECT sensor or MAP sensor

Faulty injector

Faulty ECM

Others

Excessive combustion chamber deposits

ECT sensor or MAP sensor in
Section 6E.
Fuel injector injection volume inspec-
tion in Section 6E.
Inspection of ECM and its circuit in
Section 6E.

Piston and cylinder head cleaning in
Section 6A.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды

Suzuki GA413, Руководство по обслуживанию

Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды