manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Adhesive materials and tools required for removal and installation.

One component urethane adhesive and primers used in com-
bination (For one sheet of windshield).
Adhesive (300 g (14.1 oz.))
Primer for glass (15 g (0.5 oz.))
Primer for body (15 g (0.5 oz.))

Eyeleteer

Piano string

Brush for primer application (2 pcs)

Knife

Rubber sucker grip

Sealant gun (for filling adhesive)

Putty spatula (for correcting adhered parts)

REMOVAL

1) Clean both inside and outside of glass and around it.
2) Remove wiper arms.
3) Remove garnish and stoppers.
4) Using tape, cover body surface around glass to prevent any

damage.

5) Remove instrument panel and head lining.

6) Remove rear view mirror, sunvisor, front pillar trims and then

windshield trims from front pillars (right & left).

7) Remove (or cut) windshield molding all around until windshield

edge comes out.

8) Cut adhesive all around glass with windshield knife.

If cut with piano string, follow step 9) and 10).

9) Drill hole with eyeleteer through adhesive and let piano string

through it.

1. Eyeleteer

BODY SERVICE

9-17

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 2
Yakima K1005 Instructions Manual preview
K1005
Бренд: Yakima Страницы: 12
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Бренд: Kia Страницы: 10
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Бренд: Toyota Страницы: 52
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Бренд: Brodit Страницы: 2
Volvo XC60 2014 Wiring Diagrams preview
XC60 2014
Бренд: Volvo Страницы: 362
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Бренд: Honda Страницы: 410
Volvo XC70 - ANNEXE 808 Quick Manual preview
XC70 - ANNEXE 808
Бренд: Volvo Страницы: 8
Xforce PR-104 User Manual preview
PR-104
Бренд: Xforce Страницы: 11
Black Horse Off Road TR-JECOOE Installation Instructions preview
TR-JECOOE
Бренд: Black Horse Off Road Страницы: 3
v.link VL2-CIC Manual preview
VL2-CIC
Бренд: v.link Страницы: 15
Macally HRMOUNTPROTRAY User Manual preview
HRMOUNTPROTRAY
Бренд: Macally Страницы: 19
TAUBENREUTHER 2360-00 Manual preview
2360-00
Бренд: TAUBENREUTHER Страницы: 10
Rand McNally tnd 760 User Manual preview
tnd 760
Бренд: Rand McNally Страницы: 60
Honda 2011 Pilot Owner'S Manual preview
2011 Pilot
Бренд: Honda Страницы: 574
Terex TA400 Operation Manual preview
TA400
Бренд: Terex Страницы: 177
Sirius Satellite Radio S50 User Manual preview
S50
Бренд: Sirius Satellite Radio Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды