manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

BRAKES

5-7

BOOSTER ASSEMBLY

GENERAL DESCRIPTION

The booster is located between the master cylinder and the brake pedal. It is so designed that the force created
when the brake pedal is depressed is mechanically increased combined with the engine vacuum.

CAUTION:
When and after removing booster, never drop or deform it.

WARNING:
Never disassemble brake booster assembly. If it is found faulty, replace it with new assembly.

CAUTION:
The torque values specified are for dry, unlubricated fasteners. If any hydraulic component is re-
moved or brake line disconnected, bleed the brake system.

A. Brake pedal
B. Master cylinder
1. Booster No.1 body
2. Booster No.2 body
3. Valve operating rod
4. Air cleaner element
5. Air cleaner separator
6. Air valve spring retainer
7. Air valve return spring
8. Control valve spring retainer
9. Control valve spring

10. Booster control valve
11. Booster air valve
12. Booster piston
13. Valve stopper key
14. Booster diaphragm
15. Reaction disc
16. Booster piston return spring
17. Booster piston rod
18. Booster rod adjust screw

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 94
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Бренд: Q'STRAINT Страницы: 10
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Бренд: Wilco Offroad Страницы: 4
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Бренд: TATA Motors Страницы: 236
Flash Cover MN002 Installation Manual preview
MN002
Бренд: Flash Cover Страницы: 2
JKS JKSOGS960 Installation Instructions Manual preview
JKSOGS960
Бренд: JKS Страницы: 6
Thule 953000 Instructions Manual preview
953000
Бренд: Thule Страницы: 8
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Бренд: Bracketron Страницы: 4
Hama MagLock Vent Operating Instructions Manual preview
MagLock Vent
Бренд: Hama Страницы: 39
G-Tech Pro Competition User Manual preview
Pro Competition
Бренд: G-Tech Страницы: 180
Rola RCLSH Fitting Instructions preview
RCLSH
Бренд: Rola Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды