manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL LEAKAGE CHECK PROCEDURE

After performing any service on fuel system, check to make sure
that there are no fuel leakages as follows.
1) Turn the ignition switch ON position for 3 seconds (to operate

fuel pump) and then turn it OFF position.
Repeat this (ON and OFF) 3 or 4 times and apply fuel pressure
to fuel line (till fuel pressure is felt by hand placed on fuel return
hose).

2) In this state, check to see that there are no fuel leakages from

any part of fuel system.

ON-BOARD DIAGNOSTIC SYSTEM

Refer to “On-Board Diagnostic System” in Section 6E.

PRECAUTION IN DIAGNOSING TROUBLES

Be sure to read “Precaution in Diagnosing Troubles” in Section 6E
and observe what is written there.

6-4

ENGINE

ENGINE DIAGNOSIS

This vehicle is equipped with an engine and emission control system, which controls the A / F mixture, ignition tim-
ing, emission, etc. suitably to engine conditions by ECM. ECM has an On-Board Diagnostic system which detects
a malfunction in this system.
When diagnosing a trouble in the engine including this system, be sure to have understanding of the outline of “On-
Board Diagnostic system” and each item in “Precaution in Diagnosing Trouble” and follow “ENGINE DIAGNOSTIC
FLOW TABLE” given below to obtain correct result smoothly.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Бренд: GMC Страницы: 140
Back View RV-250 User Manual preview
RV-250
Бренд: Back View Страницы: 168
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Бренд: hager Страницы: 9
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Бренд: Gatorback Mudflaps Страницы: 4
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Бренд: Q Mobility Group Страницы: 9
Porsche 01-B Web Application Manual preview
01-B
Бренд: Porsche Страницы: 313
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Бренд: FALCON RIDGE Страницы: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Бренд: Volvo Страницы: 30
Ford 2005 P207 Explorer Sport Trac Owner'S Manual preview
2005 P207 Explorer Sport Trac
Бренд: Ford Страницы: 540
Volvo 164 1969 Service Manual preview
164 1969
Бренд: Volvo Страницы: 266
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Бренд: I.D. Systems Страницы: 41
JCROffroad JEEP GL ADIATOR JT TOPPER ROOF RACK Install Instructions Manual preview
JEEP GL ADIATOR JT TOPPER ROOF RACK
Бренд: JCROffroad Страницы: 7
Vecow IVH-9000-2R440Q User Manual preview
IVH-9000-2R440Q
Бренд: Vecow Страницы: 110
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
NavLinkz RL4-ELINK Manual preview
RL4-ELINK
Бренд: NavLinkz Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды