manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

5) Install brake shoes, referring to steps 1) to 3) of BRAKE SHOE

INSTALLATION.

6) Install brake drum. (Refer to steps 1) and 2) of BRAKE DRUM

INSTALLATION of this section.

7) Fill reservoir with brake fluid and bleed brake system. (For

bleeding operation, refer to BLEEDING BRAKES.)

8) Upon completion of all jobs, turn adjuster upward by flat-head

screw driver and depress brake pedal with about 30 kg (66 lbs)
load three to five times so as to obtain proper drum-to-shoe
clearance.
Adjust parking brake cable. (For adjustment, refer to PARK-
ING BRAKE CHECK AND ADJUSTMENT.)

9) Install console box.

10) Install wheel and tighten wheel nuts to specified torque. (Refer

to TIGHTENING TORQUE SPECIFICATIONS.)

11) Check to ensure that brake drum is free from dragging and

proper braking is obtained. Then remove vehicle from hoist
and perform brake test (foot brake and parking brake).

12) Check each installed part for oil leakage.

BRAKE BACK PLATE

REMOVAL

1) Perform steps 1) to 6) of BRAKE DRUM REMOVAL.
2) Perform steps 2) to 4) of BRAKE SHOE REMOVAL.
3) Perform steps 3) to 4) of WHEEL CYLINDER REMOVAL.
4) Remove parking brake cable from brake back plate by squeez-

ing parking brake cable stopper ring.

1. Stopper ring
2. Brake back plate

5) Drain rear differential gear oil.
6) Remove brake back plate bolts.
7) Draw out rear axle shaft with brake back plate, refer to REAR

AXLE SHAFT REMOVAL in Section 3E.

8) Remove wheel bearing, refer to WHEEL BEARING REMOVAL

in Section 3E.

9) Remove brake back plate from axle shaft.

1. Brake back plate
2. Plate bolt

INSTALLATION

1) Install brake back plate to axle shaft.
2) Press-fit wheel bearing and retainer ring, refer to WHEEL

BEARING INSTALLATION in Section 3E.

BRAKES

5-43

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 94
Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Бренд: GMC Страницы: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Бренд: Prorack Страницы: 15
Masterack RM470057 Assembly Instructions preview
RM470057
Бренд: Masterack Страницы: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Бренд: Over Armour Offroad Страницы: 5
Toyota 1973 Crown Hardtop Owner'S Manual preview
1973 Crown Hardtop
Бренд: Toyota Страницы: 50
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Бренд: Raytel LLC Страницы: 40
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Бренд: Jaeger Страницы: 17
Volvo 164 1969 Service Manual preview
164 1969
Бренд: Volvo Страницы: 266
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Бренд: walser Страницы: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Бренд: Mercedes-Benz Страницы: 373
ULTIMATE SPEED 290923 Operation And Safety Notes preview
290923
Бренд: ULTIMATE SPEED Страницы: 56
KlipXtreme Ridesmart KMA-610 Manual preview
Ridesmart KMA-610
Бренд: KlipXtreme Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды