manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL PUMP ASSEMBLY (WITH FUEL FIL-
TER, LEVEL GAUGE, FUEL CUT VALVE AND
TANK PRESSURE CONTROL VALVE)

Fuel pump assembly consists of fuel pump, fuel filter, fuel sender
(level) gauge (sensor), fuel cut valve and tank pressure control
valve.

Fuel Pump

When power is supplied to fuel pump, motor in pump assembly ro-
tates impeller.
This causes a pressure difference to occur between both sides of
impeller as there are many grooves around it. Then fuel is drawn
through inlet port, and with its pressure increased it is discharged
through outlet port.

Fuel Cut Valve

Fuel cut valve consists of float and spring. It allows only fuel vapor
to flow into canister and prevents fuel from flowing into canister.

Tank pressure control valve (relief valve and 2-way check
valve)

Tank pressure control valve maintains inner pressure of fuel tank
constant to prevent fuel from blowing out and fuel tank from being
deformed. Relief valve is provided to prevent discharged pressure
in fuel tank from rising excessively and 2-way check valve is pro-
vided to maintain pressure in fuel tank at a constant level so that
fuel will not blow out or tank will not be deformed.

1. Fuel pump
2. Fuel suction filter
3. Fuel filter
4. Fuel level gauge
5. Tank pressure 

control valve

6. Relief valve
7. 2-way check valve
8. Fuel cut valve
9. Fuel pump ass’y

: Fuel flow

FUEL FILLER CAP

A ratchet tightening device on threaded fuel filler cap reduces the
chances of incorrect installation, which would prevent sealing fuel
vapors.
After gasket on fuel filler cap and filler neck flange contact, ratchet
produces a loud clicking noise, indicating the seal has been set.
This cap has a vacuum relief valve inside (if equipped).
Vacuum relief valve opens to relieve vacuum created in fuel tank.

1. Vacuum relief valve (if equipped)
2. Gasket

ENGINE FUEL

6C-3

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Бренд: DANA Страницы: 42
dallara F305 Manual preview
F305
Бренд: dallara Страницы: 37
Yakima BOA Installation Instructions Manual preview
BOA
Бренд: Yakima Страницы: 8
Vauxhall Cascada Quick Reference Manual preview
Cascada
Бренд: Vauxhall Страницы: 2
Yakima StickUp Installation Instructions Manual preview
StickUp
Бренд: Yakima Страницы: 21
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Бренд: FAAFTECH Страницы: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Бренд: AutoMaxi Страницы: 2
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Бренд: Ford Страницы: 256
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Бренд: RAM Страницы: 496
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
PEUGEOT 108 2017 Vehicle Instruction Card preview
108 2017
Бренд: PEUGEOT Страницы: 17
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Бренд: Waeco Страницы: 204
K40 ELECTRONICS K40 Platinum360 Owner'S Manual preview
K40 Platinum360
Бренд: K40 ELECTRONICS Страницы: 11
Scosche MAGICGRIP MGQDWD-CPO Instructions Manual preview
MAGICGRIP MGQDWD-CPO
Бренд: Scosche Страницы: 12
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Бренд: Smappee Страницы: 28
Chevrolet LUMINA 1995 Owner'S Manual preview
LUMINA 1995
Бренд: Chevrolet Страницы: 324
TERAFLEX 1365000 Manual preview
1365000
Бренд: TERAFLEX Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды