Suzuki GA413 Скачать руководство пользователя страница 930 | Manualshive

Страница: 930 / 1246

background image

EVAPORATIVE EMISSION (EVAP) CONTROL
SYSTEM

EVAP CANISTER PURGE INSPECTION

NOTE:
Before inspection, check to make sure that gear shift lever is
in neutral position and that parking brake lever is pulled all the
way up.

1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose and check

that vacuum is not felt there when engine is cool and running at
idle speed.

3) Connect purge hose to EVAP canister and warm up engine to

normal operating temperature.

4) Turn ignition switch OFF.
5) Restart engine and run it at 2000 r/min. for 2 min. or more.
6) Disconnect purge hose from EVAP canister.
7) Also check that vacuum is felt when engine is running at 3000

r/min.

NOTE:
ECM detects a change in the purge fuel vapor concentra-
tion and sometimes stops purging for several seconds but
this is nothing abnormal.

8) If vacuum is not felt in Step 7), run engine at idle for 8 min. or

more and then repeat check in Step 7).

If check result is not satisfactory in Steps 2) and 8), check vacuum
passage, hoses, EVAP canister purge valve, wire harness and ECM.

VACUUM PASSAGE INSPECTION

Start engine and run it at idle speed. Disconnect vacuum hose (1)
from EVAP canister purge valve (2). With finger placed against
hose disconnected, check that vacuum is applied.
If it is not applied, clean vacuum passage by blowing compressed
air.

VACUUM HOSE INSPECTION

Check hoses for connection, leakage, clog and deterioration. Re-
place as necessary.

6E-38

ENGINE AND EMISSION CONTROL SYSTEM

GA413
supple

«
...
928
929
930
931
932
...
»

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Бренд: Acdeos Страницы: 7

Бренд: GARO Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: E&G Classics Страницы: 3

GMC Yukon Denali 2005

Бренд: Cadillac Страницы: 456

Бренд: Saab Страницы: 63

Бренд: R&G Страницы: 20

Бренд: Whispbar Страницы: 70

Бренд: ConWys AG Страницы: 16

Бренд: JBL Страницы: 12

Бренд: AutoLoc Страницы: 6

Бренд: Rydeen Страницы: 14

Бренд: Menabo Страницы: 8

Бренд: Seat Страницы: 372

Black Bison Sports Series

Бренд: Wald Страницы: 7

Бренд: DiscountRamps Страницы: 2

84 64 0 025 810

Бренд: BMW Страницы: 25

YARIS SEDAN 2019

Бренд: Toyota Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды