manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

INSPECTION AND ADJUSTMENT
Push Rod Clevis Length

Check that dimension “a” as shown is within 99.5 – 100.5 mm (3.92
– 3.99 in.) and torque nut to specification.

Dimension “a”: 99.5 – 100.5 mm ( 3.92 – 3.99 in.)

Tightening Torque
(b): 25 N·m (2.5 kg-m, 18.0 lb-ft)

NOTE:
Whenever booster was removed, make sure to check clear-
ance between piston rod and master cylinder piston. (For de-
tails, refer to following procedure.)

1. Push rod clevis
2. Nut

Booster Piston Rod and Master Cylinder Piston 
Clearance

The length of booster piston rod is adjusted to provide specified
clearance ”a” between piston rod end and master cylinder piston.

1. Booster piston rod
2. Master cylinder piston

Before measuring clearance, push piston rod several times so
as to make sure reaction disc is in place.

Keep inside of booster at atmospheric pressure for measure-
ment.

1) Set special tool (A) on master cylinder and push pin until con-

tacts piston.

Special Tool 
(A) : 09950-96010

1. Master cylinder
2. Piston
3. Pin head

2) Turn special tool upside down and place it on booster. Adjust

booster piston rod length until rod end contacts pin head.

Special Tool 
(A) : 09950-96010

Clearance ”b” : 0 mm (0 in.)

NOTE:
Take measurement with booster set vertically and rod at
the center, or with piston rod fixed by screw driver.

1. Booster body
2. Piston rod

BRAKES

5-51

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

PAC I GM3 Instruction Manual preview
I GM3
Бренд: PAC Страницы: 15
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Бренд: GMC Страницы: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Бренд: Prorack Страницы: 15
Yescom YES5062 User Manual preview
YES5062
Бренд: Yescom Страницы: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Бренд: Z Automotive Страницы: 16
Dakota Digital MCL-7000 Series Quick Start Manual preview
MCL-7000 Series
Бренд: Dakota Digital Страницы: 2
Volvo 2010 C30 Owner'S Manual preview
2010 C30
Бренд: Volvo Страницы: 284
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Бренд: Xblitz Страницы: 30
Parkeon StradaPAL Installation Manual preview
StradaPAL
Бренд: Parkeon Страницы: 43
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Бренд: Volvo Страницы: 262
Club Car TransPorter 4 Maintenance And Service Manual preview
TransPorter 4
Бренд: Club Car Страницы: 286
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Бренд: Waeco Страницы: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Бренд: Or-Fab Страницы: 4
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
Prorack K947 Fitting Instructions Manual preview
K947
Бренд: Prorack Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды