manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING:

After deployment, the metal surfaces of the air bag
(inflator) module will be very hot. Do not touch the
metal areas of them for about 30 minutes after de-
ployment.

Do not place the deployed air bag (inflator) module
near any flammable objects.

Do not apply water, oil, etc. to deployed air bag (in-
flator) module.

If the deployed air bag (inflator) module must be
moved before it is cool, wear gloves and handle it
by using nonmetal material such as the air bag and
vinyl trim.

Failure to follow procedures may result in fire or per-
sonal injury.

12) Separate the two banana plugs on the deployment harness.
13) Connect the deployment harness to the power source (12V

vehicle battery) to immediately deploy the air bag.

14) Disconnect the deployment harness from power source (12V

vehicle battery) and short the two deployment harness leads
together by fully seating one banana plug into the other.

15) In the unlikely event that the air bag (inflator) module did not

deploy after following these procedures, proceed immediately
with Steps 20) through 23). If the air bag (inflator) module did
deploy, proceed with Steps 16) through 19).

16) Put on a pair of shop gloves to protect your hands from pos-

sible irritation and heat when handling the deployed air bag (in-
flator) module.

17) Disconnect the deployment harness from the air bag (inflator)

module as soon after deployment as possible.
NOTE:
This will prevent damage to the deployment harness due
to possible contact with the hot air bag (inflator) module.
The deployment harness are designed to be reused. They
should, however, be inspected for damage after each de-
ployment and replaced if necessary.

1. Connect one banana plug to positive terminal of pow-

er source (12V vehicle battery) and then the other to
negative terminal to immediately deploy.

2. Short to two deployment harness leads.

AIR BAG SYSTEM

10B-51

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

iDataLink Maestro Installation Manual preview
Maestro
Бренд: iDataLink Страницы: 9
Back View RV-250 User Manual preview
RV-250
Бренд: Back View Страницы: 168
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Бренд: ZAPTEC Страницы: 20
Streetwize SWGH3 Quick Start Manual preview
SWGH3
Бренд: Streetwize Страницы: 4
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Бренд: Honda Страницы: 410
Volkswagen Zubehör 000 071 105 D Installation Instructions Manual preview
000 071 105 D
Бренд: Volkswagen Zubehör Страницы: 133
Yenkee YAC 450 User Manual preview
YAC 450
Бренд: Yenkee Страницы: 22
Kia 2015 optima Quick Start Manual preview
2015 optima
Бренд: Kia Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды