manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6-36

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP

DOES NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE
AT STOP)

CIRCUIT DESCRIPTION

1. Main fuse box
2. Ignition switch
3. Fuse box
4. Main relay
5. Malfunction indicator lamp

in combination meter

6. “IG COIL METER” fuse
7. Monitor connector 

(if equipped)

When the ignition switch is turned ON, ECM causes the main relay to turn ON (close the contact point). Then, ECM
being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the engine starts to run
and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is detected, MIL remains
ON even when the engine is running.

INSPECTION

STEP

ACTION

YES

NO

1

MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in com-
bination meter comes ON?

Go to Step 2.

Main fuse blown, ignition switch
malfunction, “BLK/WHT” circuit
between “IG COIL METER” fuse
and combination meter or poor
coupler connection at combination
meter.

2

ECM Power and Ground Circuit Check
Does engine start?

Go to Step 3.

Go to TABLE A-3 ECM POWER
AND GROUND CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in Section 8G.

3

MIL Circuit Check
1) Turn ignition switch OFF and discon-

nect connectors from ECM.

2) Check for proper connection to ECM

at terminal L20-7.

3) If OK, then using service wire, ground

terminal L20-7 in connector discon-
nected.

Does MIL turn on at ignition switch ON?

Test switch terminal cir-
cuit shorted to ground
or “PNK/WHT” wire
shorted to ground (ve-
hicle with monitor con-
nector).
Substitute a known-
good ECM and recheck.

Bulb burned out, “PPL/YEL” wire
circuit open or “PNK/WHT” wire
shorted to ground.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Бренд: TATA Motors Страницы: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Бренд: TAUBENREUTHER Страницы: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Бренд: Yakima Страницы: 15
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Бренд: Mercedes-Benz Страницы: 358
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
A-Tach Mounts 50232 Instructions preview
50232
Бренд: A-Tach Mounts Страницы: 2
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Бренд: Waeco Страницы: 204
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Бренд: Coolster Страницы: 45
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
ULTIMATE SPEED UKLL 5 A1 Operating Instructions Manual preview
UKLL 5 A1
Бренд: ULTIMATE SPEED Страницы: 132
VDO ELECTRONIC SPEEDOMETER 1323 Datasheet preview
ELECTRONIC SPEEDOMETER 1323
Бренд: VDO Страницы: 2
v.link VL2-CONCERT Manual preview
VL2-CONCERT
Бренд: v.link Страницы: 20
MSD 7222 Installation Instructions Manual preview
7222
Бренд: MSD Страницы: 16
Emerson ATEX Reference Manual preview
ATEX
Бренд: Emerson Страницы: 24
Emerson Fisher 1051 Instruction Manual preview
Fisher 1051
Бренд: Emerson Страницы: 32
Toyota 2005 ECHO User Manual preview
2005 ECHO
Бренд: Toyota Страницы: 433

Бренды по названию

Популярные бренды

Загрузить еще бренды