manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DIAGNOSIS

GENERATOR

UNDERCHARGED BATTERY

This condition, as evidenced by slow cranking or indicator clear
with red dot can be caused by one or more of the following condi-
tions even though indicator lamp may be operating normal.
Following procedure also applies to cars with voltmeter and amme-
ter.
1) Make sure that undercharged condition has not been caused by

accessories left on for extended period of time.

2) Check drive belt for proper tension.
3) If battery defect is suspected, refer to Battery section.
4) Inspect wiring for defects. Check all connections for tightness

and cleanliness, battery cable connections at battery, starting
motor and ignition ground cable.

5) Connect voltmeter and ammeter as shown in left figure.

Voltmeter
Set between generator B terminal and ground.

Ammeter
Set between generator B terminal and battery (+) terminal.

NOTE:
Use fully charged battery.

6) Measure current and voltage.

1. Generator
2. Ammeter
3. Voltmeter

4. Battery
5. Load
6. Switch

Ammeter between generator (B)
terminal and battery (+) terminal.

Voltmeter between
generator (B) termi-
nal and ground.

Volt

Temperature

No-load Check

1) Run engine from idling up to 2,000 rpm and read meters.

NOTE:
Turn off switches of all accessories (wiper, heater etc.).

Standard current: 10 A maximum

Standard voltage: 14.4 – 15.0 V (at 20 C, 68 F)

NOTE:
Consideration should be taken that voltage will differ
somewhat with regulator case temperature as shown in left
figure.

CHARGING SYSTEM

6H-3

GA413
supple

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Ranger design 5044 Installation Manual preview
5044
Бренд: Ranger design Страницы: 6
A-Tach Mounts ST-1 Instructions preview
ST-1
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50206 Instructions preview
50206
Бренд: A-Tach Mounts Страницы: 2
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Бренд: Jeep Страницы: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Бренд: Jeep Страницы: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Бренд: Jeep Страницы: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Бренд: Jeep Страницы: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Бренд: Jeep Страницы: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Бренд: Jeep Страницы: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Бренд: Jeep Страницы: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Бренд: Jeep Страницы: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Бренд: Jeep Страницы: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Бренд: Jeep Страницы: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Бренд: Jeep Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды