manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6-72

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

INSPECTION

NOTE:
If starter circuit is open (i.e., start signal circuit is OK but starter fails to run), this DTC is stored in memory
at starter switch ON, even though CKP sensor is in good condition.
When starter motor fails to run and this DTC appears, check starter circuit first.

STEP

ACTION

YES

NO

1

Was “ENGINE DIAG. FLOW TABLE” performed?

Go to Step 2.

Go to “ENGINE DIAG.
FLOW TABLE”.

2

Is there DTC P1500 (Engine starter signal circuit)?

Go to DTC P1500
Diag. Flow Table.

Go to Step 3.

3

Check CKP Sensor for Resistance.

1) Disconnect CKP sensor connector with ignition

switch OFF.

2) Then check for proper connection to CKP sensor at

“RED/BLU” and “WHT/BLU” wire terminals.

3) If OK, measure sensor resistance between termi-

nals. See Fig. 1.

CKP sensor resistance: 360 – 460 

 at 20

C, 68

F

4) Measure resistance between each terminal and

ground.

Insulation resistance: 1 M

 or more.

Were measured resistance values in step 3) and 4) as
specified?

Go to Step 4.

Replace CKP sensor.

4

Check visually CKP sensor and pulley for the follow-
ing. See Fig.2.

Damage

No foreign material attached.

Correct installation.

Are they in good condition?

“RED/BLU” or 
“WHT/BLU” wire open
or shorted to ground,
or poor connection at
C23-7 or C23-15.
If wire and connection
are OK, intermittent
trouble or faulty ECM.
Recheck for intermit-
tent referring to “Inter-
mittent and Poor Con-
nection” in Section 0A.

Clean, repair or re-
place.

Fig. 1 for Step 3

Fig. 2 for Step 4

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

B-Speech B-Speech Prim Manual preview
B-Speech Prim
Бренд: B-Speech Страницы: 18
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Бренд: Jeep Страницы: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Бренд: Jeep Страницы: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Бренд: Jeep Страницы: 558
SnapPad EQ Round Installation Instructions preview
EQ Round
Бренд: SnapPad Страницы: 5
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Бренд: Nuna Страницы: 17
Quadratec 11113.1435 Quick Start Manual preview
11113.1435
Бренд: Quadratec Страницы: 14
Enduro EM203 User Manual preview
EM203
Бренд: Enduro Страницы: 52
FORM FIT 8F 00 Installation Instructions preview
8F 00
Бренд: FORM FIT Страницы: 2
CSL 41802 User Manual preview
41802
Бренд: CSL Страницы: 8
Kuda 191090 Installation Instruction preview
191090
Бренд: Kuda Страницы: 3
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Бренд: Menabo Страницы: 8
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Бренд: Scion Страницы: 58
Sanixair 8059606830094 Use And Maintenance preview
8059606830094
Бренд: Sanixair Страницы: 20
OMNISTOR OMNI-BIKE plus Caravan Special Manual preview
OMNI-BIKE plus Caravan Special
Бренд: OMNISTOR Страницы: 4
DIGITAL DELAY 1014-SCR Instructions Manual preview
1014-SCR
Бренд: DIGITAL DELAY Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды