manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

CARE OF BATTERY

1) The battery is a very reliable component, but needs periodical

attentions.
Keep the battery carrier clean; prevent rust formation on the ter-
minal posts; keep the electrolyte up to the upper level uniformly
in all cells.

When keeping battery on vehicle over a long period of time, fol-
low instructions given below.

Weekly, start the engine and run it until it reaches normal op-
erating temperature with engine speed of 2000 to 3000 rpm.
Make sure all electric switches are off before storing the ve-
hicle.

Recharge the battery twice a month to prevent it from dis-
charging excessively. This is especially important when am-
bient temperature is low.
The battery discharges even when it is not used, while ve-
hicles are being stored. Battery electrolyte can freeze and
battery case can crack at cold ambient condition if battery is
not properly charged.

2) Keep the battery cable connections clean.

The cable connections, particularly at the positive (+) terminal
post, tend to become corroded. The product of corrosion, or
rust, on the mating faces of conductors resists the flow of cur-
rent.
Clean the terminals and fittings periodically to ensure good met-
al-to-metal contact, and grease the connections after each
cleaning to protect them against rusting.

WARNING:

Never expose battery to open flame or electric spark
because of battery generate gas which is flammable
and explosive.

Do not allow battery fluid to contact eyes, skin, fabrics,
or painted surfaces as fluid is a corrosive acid. Flush
any contacted area with water immediately and thor-
oughly.

Batteries should always be kept out of reach of chil-
dren.

3) Be always in the know as to the state of charge of the battery.

The simplest way to tell the state of charge is to carry out a
hydrometer test. The hydrometer is an instrument for measur-
ing the specific gravity (S.G.) of the battery electrolyte. The S.G.
of the electrolyte is indicative of the state of charge. Refer to
“BATTERY” of DIAGNOSIS in this section.

CHARGING SYSTEM

6H-3

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

U.S. General 97845 Set Up And Operating Instructions preview
97845
Бренд: U.S. General Страницы: 5
Kargo Master 40131 Installation Manual preview
40131
Бренд: Kargo Master Страницы: 5
Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Бренд: Lancia Страницы: 386
Aries P35-2004 Installation Manual preview
P35-2004
Бренд: Aries Страницы: 3
HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Бренд: HUSKY LINERS Страницы: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Бренд: Volvo Страницы: 19
Yakima K1249 Instructions Manual preview
K1249
Бренд: Yakima Страницы: 9
Alfa Romeo 1966 Spider 105 Faq preview
1966 Spider 105
Бренд: Alfa Romeo Страницы: 46
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Бренд: Abrams Страницы: 12
Honda 08V31-TE0-100A Installation Instructions Manual preview
08V31-TE0-100A
Бренд: Honda Страницы: 10
Hella 2DA 008 136-031 Mounting Instructions preview
2DA 008 136-031
Бренд: Hella Страницы: 2
Toyota Avalon 2001 Operating Manual preview
Avalon 2001
Бренд: Toyota Страницы: 295
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual preview
2005-2009 Chrysler 300C
Бренд: Mopar Страницы: 7
Kuda 076100 Installation Instruction preview
076100
Бренд: Kuda Страницы: 3
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Бренд: Fleetwood Страницы: 166
Phonocar 6/946 Instruction Manual preview
6/946
Бренд: Phonocar Страницы: 4
Van Guard VG162S Fitting Instructions preview
VG162S
Бренд: Van Guard Страницы: 3
Ranger design C24-DL Installation Manual preview
C24-DL
Бренд: Ranger design Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды