manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

INSTRUMENT PANEL

WARNING:
See WARNING at the beginning of this section.

CAUTION:
For vehicle with Air Bag, instrument panel could not be
removed with SDM coupler connected.
Use care not to damage Air Bag harness.

Tightening Torque
(a): 23 N

.

m (2.3 kg-m, 17.0 lb-ft)

1. Instrument panel harness
2. Connector with bolt
3. Dash panel hole
4. Connector
5. Body ground
6. Fuse box
7. Wire harness connector bolt

8. Screw
9. Bolts

REMOVAL

1) Disconnect negative (–) cable at battery.
2) Disable air bag system, if equipped. Refer to DISABLING AIR

BAG SYSTEM in Section 10B.

3) Remove glove box and column hole cover.
4) Disconnect wires and cables from heater unit and air inlet box

assembly.

5) Remove steering column assembly. Refer to Section 3C.
6) Disconnect speedometer connector and remove speedome-

ter assembly.

7) Remove front hood opener.
8) Disconnect couplers which need to be disconnected for re-

moval for instrument panel (refer to the left figure) and pull wire
harness out of dash panel.

9) Remove instrument panel mounting screws.

10) Remove instrument panel mounting bolt.
11) Remove instrument panel with steering support member.

INSTALLATION

1) Install instrument panel by reversing removal procedure, noting

the following items.

When installing each part, be careful not to catch any cable
or wiring harness.

Connect wire harness connector with bolt securely and tight-
en its bolt to specified torque shown on the connector.

When installing steering column assembly, refer to Section
3C STEERING COLUMN INSTALLATION.

2) Adjust control cables. (Refer to Section 1A HEATER CON-

TROL CABLES.)

3) Enable air bag system if equipped. Refer to ENABLING AIR

BAG SYSTEM in Section 10B.

[Harness Location]

[Instrument Panel Fastener Location]

BODY SERVICE

9-23

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Edelbrock 6883 Instructions preview
6883
Бренд: Edelbrock Страницы: 2
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Бренд: muth Страницы: 9
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90
BURY CC 9040 Specification preview
CC 9040
Бренд: BURY Страницы: 2
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Бренд: Sumitomo Страницы: 22
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Бренд: Safe Fleet Страницы: 24
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Ford Fusion 2019 Supplement Manual preview
Fusion 2019
Бренд: Ford Страницы: 51
Car-Interface CI-RL4-R40 Manual preview
CI-RL4-R40
Бренд: Car-Interface Страницы: 25
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Бренд: Metra Electronics Страницы: 10
NavLinkz RL4-MIB3-E Manual preview
RL4-MIB3-E
Бренд: NavLinkz Страницы: 24
SportRack EXPLORER A90095 Instruction Sheet preview
EXPLORER A90095
Бренд: SportRack Страницы: 6
Volkswagen Bora 1998 Service Manual preview
Bora 1998
Бренд: Volkswagen Страницы: 339
NAV TOOL NAVTOOL6.0-AR2-HDMI Installation Manual preview
NAVTOOL6.0-AR2-HDMI
Бренд: NAV TOOL Страницы: 19
Beat-Sonic SLA-91 Instruction Manual preview
SLA-91
Бренд: Beat-Sonic Страницы: 1
Crux BEELINE Series Manual preview
BEELINE Series
Бренд: Crux Страницы: 8
Crux ACPBM-77X Manual preview
ACPBM-77X
Бренд: Crux Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды