manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

REMOVAL

1) Disconnect negative cable at battery.
2) Open glove box, then while pressing glove box stopper, pull out

glove box from instrument panel and then remove glove box cir-
clip and glove box from instrument panel.

3) Disable air bag system. Refer to DISABLING AIR BAG SYS-

TEM of SERVICE PRECAUTIONS in this section.

4) Remove passenger air bag (inflator) module attaching bolts

and screws and passenger air bag (inflator) module from ve-
hicle.

1. Glove box
2. Glove box circlip
3. Passenger air bag (inflator) module
4. Instrument panel
5. Harness cover

INSPECTION

WARNING:
Never measure resistance of passenger air bag (inflator)
module or disassemble it. Otherwise personal injury may
result.

CAUTION:
If air bag (Inflator) module was dropped from a height or
90 cm (3 ft) or more, it should be replaced.

Check air bag (inflator) module appearance visually for following
symptoms and if any one of them is applicable, replace with a new
one.

Air bag has deployed.

There is a crack in trim cover (pad surface).

Wire harness or connector is damaged.

Air bag (inflator) module is damaged or a strong impact (e.g.,
dropping) was applied to it.

AIR BAG SYSTEM

10B-45

PASSENGER AIR BAG (INFLATOR) MODULE (IF EQUIPPED)

WARNING:

Never attempt to disassemble or repair the passenger air bag (inflator) module. If any abnormality
is found, be sure to replace it with new one as an assembly.

Be sure to read SERVICE PRECAUTIONS in this section before starting to work and observe every
precaution during work. Neglecting them may result in personal injury or undeployment of the air
bag when necessary.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Metra Electronics 95-6556 Installation Instructions preview
95-6556
Бренд: Metra Electronics Страницы: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Бренд: Rostra Страницы: 2
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Бренд: hc-cargo Страницы: 60
Toro 137-1019 Installation Instructions Manual preview
137-1019
Бренд: Toro Страницы: 24
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Бренд: Columbia Страницы: 14
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
Wagan Easy Air Auto Screen User Manual preview
Easy Air Auto Screen
Бренд: Wagan Страницы: 8
Edelbrock 8135 Installation Instructions preview
8135
Бренд: Edelbrock Страницы: 4
Whispbar K482W Fitting Instructions Manual preview
K482W
Бренд: Whispbar Страницы: 14
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Roadefend RDT401P Instruction Book preview
RDT401P
Бренд: Roadefend Страницы: 15
FALCON RIDGE CF-U-1000-RW02 Instructions For Installation And Care preview
CF-U-1000-RW02
Бренд: FALCON RIDGE Страницы: 8
VanEssa mobilcamping 00001668 Installation Manual preview
00001668
Бренд: VanEssa mobilcamping Страницы: 12
Toyota 2005 Camry ACV30 Series Wiring Diagram preview
2005 Camry ACV30 Series
Бренд: Toyota Страницы: 251
Toyota 2003 ECHO Owner'S Manual preview
2003 ECHO
Бренд: Toyota Страницы: 276
Toy State 007 Nikko Radio Control Top Secret R/C 62070 Owner'S Manual preview
007 Nikko Radio Control Top Secret R/C 62070
Бренд: Toy State Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды