manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

8A-0-1

8A

Precautions

• When disconnecting the battery terminals, be sure to (1) turn off the ignition switch and all other switches,(2)

disconnect the negative (-) terminal wire and then (3) disconnect the positive (+) terminal wire.Connect the
wires in the reverse order of disconnecting.

• When disconnecting the connectors, be sure to unlock the connector lock (if equipped) and then pull the

connector shells to detach them. Do not pull the wires.

• Connect the connectors by holding the connector shells. Make sure they are securely locked.
• Install the wiring harness securely without any slack. 

• When installing parts, make sure the wiring harness is not interfered with or pinched by them.
• Avoid routing the wiring harness near or around a sharp corner or edge of the vehicle body or parts as much

as possible. If necessary, protect the wiring harness by winding tape or the like around on it.

• When replacing a fuse, make sure to use the specified capacity fuse. Using a fuse with a larger capacity can

cause damage to the electrical parts or a fire.

• Do not handle electrical/ electronic parts (computer, relay, etc.) roughly or drop them.
• Do not expose electrical/ electronic parts to high temperature (Approximately 80°C(176°F) or higher) or

water.

• For open back connectors,be sure to insert the tester probe into the back side (wiring harness side) of the

connector for inspection.For sealed back connectors,apply the tester probe to the terminal as gently as pos-
sible not to damage or deform the terminal.

Air bag/seat belt pretensioner Warnings

Service manual

EXAMPLE

CD

WARNING:

(For the vehicles with the Supplemental Restraint System (Air Bags) and/or the Seat Belt Pretensioner
System)
Service on or around the air bag system / Seat belt pretensioner system components or their wiring
must be performed only by an authorized SUZUKI dealer. Observe all the warnings in the service man-
ual and disable the systems before servicing on or around the components and the wiring of the sys-
tems. The service manual(s) is (are) mentioned in the FOREWORD of this manual. Failure to follow the
Warnings could result in unintended activation of the systems or could render the systems inopera-
tive. Either of these two conditions may result in severe injury.

CAUTION:

To prevent damage to the electrical/ electronic parts (especially computers or semi-conductors) or to
prevent fire.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Бренд: Jeep Страницы: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Бренд: Jeep Страницы: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 525
Kuda-Phonebase 055040 Installation Instruction preview
055040
Бренд: Kuda-Phonebase Страницы: 3
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Бренд: Whipple Страницы: 3
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Бренд: Jaeger Страницы: 17
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Jeep 2014 Grand Cherokee SRT8 Owner'S Manual preview
2014 Grand Cherokee SRT8
Бренд: Jeep Страницы: 596
Skoda 1K0 051 437 Assembly Instructions preview
1K0 051 437
Бренд: Skoda Страницы: 4
Whispbar K919W Fitting Instructions Manual preview
K919W
Бренд: Whispbar Страницы: 17
Opel 2013 Corsa Brochure & Specs preview
2013 Corsa
Бренд: Opel Страницы: 32
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Бренд: Valeo Страницы: 25
Subaru 2003 Baja Owner'S Manual preview
2003 Baja
Бренд: Subaru Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды