manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DIAGNOSIS

To ensure that the trouble diagnosis is done accurately and
smoothly, observe “Precautions in Diagnosing Troubles” and fol-
low “ABS Diagnostic Flow Table”.

PRECAUTION IN DIAGNOSING TROUBLES

If the vehicle was operated in any of the following ways, “ABS”
warning light may light momentarily but this does not indicate
anything abnormal in ABS.

– The vehicle was driven with parking brake pulled.
– The vehicle was driven with brake dragging.
– The vehicle was stuck in mud, sand, etc.
– Wheel spin occurred while driving.
– Wheel(s) was rotated while vehicle was jacked up.

Be sure to read “Precautions for Electronic Circuit Service” in
“GENERAL INFORMATION” section before inspection and ob-
serve what is written there.

Be sure to use the trouble diagnosis procedure as described in
the flow table. Failure to follow the flow table may result in incor-
rect diagnosis. (Some other diag. trouble code may be stored by
mistake in the memory of ABS control module during inspec-
tion.)

5E-6

ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Бренд: Romik Страницы: 6
U.S. General 95904 Operating Instructions preview
95904
Бренд: U.S. General Страницы: 4
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
P-Invent Troller User Manual preview
Troller
Бренд: P-Invent Страницы: 4
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Бренд: Buick Страницы: 20
MVG 0845 C Manual preview
0845 C
Бренд: MVG Страницы: 18
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Бренд: Abrams Страницы: 12
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107
Rydeen BSS2 Owner'S Manual preview
BSS2
Бренд: Rydeen Страницы: 14
Chrysler Dodge Caravan 2002 Manual preview
Dodge Caravan 2002
Бренд: Chrysler Страницы: 2399
Ednet 84104 User Manual preview
84104
Бренд: Ednet Страницы: 6
Chevrolet 1995 C/K Pickup Owner'S Manual preview
1995 C/K Pickup
Бренд: Chevrolet Страницы: 483
HOLDEN Malibu EM 2015 Owner'S Handbook Manual preview
Malibu EM 2015
Бренд: HOLDEN Страницы: 330
MayPole BC2085 Manual preview
BC2085
Бренд: MayPole Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды