manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

1. Screw
2. Steering column upper cover
3. Steering column lower cover

2) Remove steering column cover screws (3 pcs).
3) Loosen steering column mounting bolts (Refer to STEERING

COLUMN in this section).

4) Separate upper cover and lower cover, then remove them.
5) If equipped with air bag system, disconnect yellow connector

and horn connector of contact coil from harness.

*: Standard screw
**: Tapping screw

3

2

**1

*1

6) Remove combination switch/contact coil and combination

switch assembly from steering column.

7) Disconnect 3 connectors from combination switch.

1. Contact coil and

combination switch
assembly

2. Connector

INSPECTION

For vehicle with air bag system
Check contact coil and combination switch wire harness for any
signs of scorching, melting or other damage. If it is damaged, re-
place it as an assembly.

1. Contact coil and combination switch assembly
2. To horn and driver air bag (inflator) module
3. To air bag wire harness

INSTALLATION

1) Check to make sure that vehicle’s front tires are set at straight-

ahead position and then ignition switch is at “LOCK” position.

2) Connect all connectors that have been disconnected in RE-

MOVAL of COMBINATION SWITCH/CONTACT COIL AND
COMBINATION SWITCH ASSEMBLY in this section.

3) Install combination switch/contact coil and combination switch

assembly to steering column.

NOTE:
For vehicle with air bag system
New contact coil and combination switch assembly is sup-
plied with contact coil set and held at its center position
with a lock pin and seal. Remove this lock pin after instal-
ling contact coil and combination switch assembly to
steering column.

1. Seal and lock pin if equipped, remove lock pin after

installing contact coil and combination switch assembly.

2. Contact coil and combination switch assembly
3. Connector

STEERING WHEEL AND COLUMN

3C-9

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

JANE be cool boosty Manual preview
be cool boosty
Бренд: JANE Страницы: 21
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Бренд: CITROEN Страницы: 52
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Бренд: GMC Страницы: 433
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Ford 2005 P207 Explorer Sport Trac Owner'S Manual preview
2005 P207 Explorer Sport Trac
Бренд: Ford Страницы: 540
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Бренд: Demco Страницы: 4
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Бренд: PUTCO Страницы: 2
Xingyun XY40EV Service Manual preview
XY40EV
Бренд: Xingyun Страницы: 74
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Бренд: Honda Страницы: 22
Mercedes-Benz 2013 CL Operator'S Manual preview
2013 CL
Бренд: Mercedes-Benz Страницы: 494
Green Valley 601951 Instructions Manual preview
601951
Бренд: Green Valley Страницы: 17
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2
Whispbar K423W Fitting Instructions Manual preview
K423W
Бренд: Whispbar Страницы: 18
travall TDG1166 Fitting Instructions preview
TDG1166
Бренд: travall Страницы: 4
Haltech TMS-4 Quick Start Manual preview
TMS-4
Бренд: Haltech Страницы: 12
Directed 933.SUBARU1 Installation Manual preview
933.SUBARU1
Бренд: Directed Страницы: 24
Erich Jaeger 735229 Installation Instructions Manual preview
735229
Бренд: Erich Jaeger Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды