manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DISASSEMBLY

1) Remove intake rocker arm with clip from rocker arm shaft, re-

move rocker arm shaft bolts and remove exhaust rocker arms
and springs by pulling its shaft out to transmission side.

2) Using special tool (Valve lifter), compress valve springs and

then remove valve cotters by using special tool (Forceps) as
shown.

Special Tool
(A): 09916-14510
(B): 09916-14910
(C): 09916-84511

3) Release special tool, and remove spring retainer and valve

spring.

4) Remove valve from combustion chamber side.

1. Valve cotters

5) Remove valve stem oil seal from valve guide, and then valve

spring seat.

NOTE:
Do not reuse oil seal once disassembled. Be sure to use
new oil seal when assembling.

1. Valve stem oil seal
2. Valve spring seat

6) Using special tool (Valve guide remover), drive valve guide out

from combustion chamber side to valve spring side.

Special Tool
(A): 09916-44910

NOTE:
Do not reuse valve guide once disassembled. Be sure to
use new valve guide (Oversize) when assembling.

7) Place disassembled parts except valve stem seal and valve

guide in order, so that they can be installed in their original posi-
tion.

6A-38

ENGINE MECHANICAL

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Compass 02106 Manual preview
02106
Бренд: Compass Страницы: 16
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Бренд: Skoda Страницы: 16
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Бренд: Safe Fleet Страницы: 12
N.R. AUTOSEATS Top User Manual preview
Top
Бренд: N.R. AUTOSEATS Страницы: 8
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Бренд: iQOS Страницы: 4
Green Valley 601951 Instructions Manual preview
601951
Бренд: Green Valley Страницы: 17
SIXTOL DRY CAR Instructions For Use Manual preview
DRY CAR
Бренд: SIXTOL Страницы: 32
NavLinkz RL4-MIB3-E Manual preview
RL4-MIB3-E
Бренд: NavLinkz Страницы: 24
CEMO 4052886280348 Manual preview
4052886280348
Бренд: CEMO Страницы: 12
HUSKY LINERS 4707 Installation Manual preview
4707
Бренд: HUSKY LINERS Страницы: 3
DV8 FBBR-04 Installation Manual preview
FBBR-04
Бренд: DV8 Страницы: 14
LAS 16143 Operating Instructions Manual preview
16143
Бренд: LAS Страницы: 9
AL-KO 811721-1 Manual preview
811721-1
Бренд: AL-KO Страницы: 40
FORM FIT HD 21D 06 Quick Manual preview
HD 21D 06
Бренд: FORM FIT Страницы: 2
Metra Electronics GMLAN29-100 Installation Instructions Manual preview
GMLAN29-100
Бренд: Metra Electronics Страницы: 8
Jaeger 21040528 Fitting Instructions Manual preview
21040528
Бренд: Jaeger Страницы: 16
Toyota PT228-89460 Manual preview
PT228-89460
Бренд: Toyota Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды