manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Tables des matières

8A

8A

8A

8A

8A

8A

8A

8A

Tables des matières

Précautions................................................... 8A-0-3
Informations générales................................ 8A-1-1

Comment lire le schéma de disposition
des connecteurs ..........................................8A-1-1
Comment lire les codes connecteur
et identifier les n° des contacts. ..................8A-1-2
Comment lire les points de mise à la
masse..........................................................8A-1-4
Légende des schémas du circuit
d’alimentation ..............................................8A-1-5
Légende des schémas des circuits
électriques ...................................................8A-1-6
Symboles et repères ...................................8A-1-8
Abréviations ..............................................8A-1-10
Symboles des codes couleur
câbles/connecteurs ...................................8A-1-11

Schéma de dispositiondes blocs
raccord de câblage ...................................... 8A-3-1

Avant ...........................................................8A-3-2

B: Faisceau de jonction,
Faisceau du moteur A/C,
Faisceauz de plafonnier A/C .....................8A-3-2
E: Faisceau de fils électriques principal ....8A-3-4

Compartiment moteur .................................8A-3-6

C: Faisceau de fils électriques de moteur .8A-3-6

Panmeau d'instruments...............................8A-3-8

E: Faisceau de fils électriques principal ....8A-3-8
Q:Faisceau de fils électriques de
sac gonflable ...........................................8A-3-11

Porte, toit ...................................................8A-3-12

J: Fil de portière avant,
Fil de portière arrière (Van) .....................8A-3-12
K: Fil de toit .............................................8A-3-12

Plancher (Van) ..........................................8A-3-14

D:Fil du commutateur de pression
d'huile ......................................................8A-3-14
L:Faisceau de fils électriques de
plancher,Fil de pompe à essence ...........8A-3-14

Plancher (Camion) ....................................8A-3-16

D:Fil du commutateur de
pression d'huile .......................................8A-3-16
L:Faisceau de fils électriques de
plancher,Fil de pompe à essence ...........8A-3-16

Porte arriere ..............................................8A-3-18

O: Faisceau de câbles de portière
de hayon arrière,Résistance
électrique de desembueur de
lunette arrière ..........................................8A-3-18

Points de masse........................................... 8A-4-1

Compartiment moteur,
Panneau d’instruments..............................8A-4-1

Schéma du circuit d'alimentation ............... 8A-5-1

Schéma du circuit d'alimentation...............8A-5-1
Fusibles et pièces protégées.....................8A-5-3

Boîte à fusibles principale .........................8A-5-3
Boîte à fusibles principale .........................8A-5-4

Schéma des circuits électriques .................8A-6-1

A-1 Systène de démarrage .......................8A-6-1
A-2 Système de charge ............................8A-6-2
A-3 Système d´allumage...........................8A-6-3
A-4 Système de refroidissement ............... 8A-6-4
A-5 Système de contrôle du moteur
(Avec capteur d´oxygène réchauffè #2) ....8A-6-6
A-5 Système de contrôle du moteur
(Sanc capteur d´oxygène réchauffè #2).. 8A-6-12
A-6 Système de commande de
l´immobilisateur ....................................... 8A-6-16
B-1 Essuie-glace et lave-glace
de pare-brise ........................................... 8A-6-17
B-2 Essuie-Glace et lave-glace
arrière...................................................... 8A-6-18
B-3 Désembueur arrière ......................... 8A-6-20
B-4 Lève-vitres électriques ..................... 8A-6-22
B-5 Verrouillage centralisé des
portes (Ancien modèle) ........................... 8A-6-24
B-5 Verrouillage centralisé des
portes (Nouveau modèle) ....................... 8A-6-25
B-7 Avertisseur ....................................... 8A-6-26
C-1 Compteur mixte
(Meter and gauge) .................................. 8A-6-27
C-2 Compteur mixte (Indicator)............... 8A-6-28
C-3 Compteur mixte
(Témoins d´avertissement) ..................... 8A-6-30
D-1 Système des phares avec
controleur DRT........................................ 8A-6-32
D-1 Système des phares sans
controleur DRT........................................ 8A-6-33
D-2 Feux de gabart,arriére et de
plaque d´immatriculation ......................... 8A-6-34
D-3 Antibrouillard arriere ......................... 8A-6-35
D-4 Dispositif d´éclairage ........................ 8A-6-36
D-5 Plafonterior ....................................... 8A-6-37
D-6 Feux clignotants et feux de
détresse .................................................. 8A-6-38
D-7 Feux stop (Van)................................ 8A-6-40
D-7 Feux stop (Camion).......................... 8A-6-41
D-8 Feux de marche arrière .................... 8A-6-42
D-9 Système de réglage des
faisceaux de phares ................................ 8A-6-43
E-1 Chauffage et climatisation ................ 8A-6-44
F-1 Système de commande des
airbags .................................................... 8A-6-46
F-2 Direction assistée ............................. 8A-6-47
F-3 Signal d´avertissement ..................... 8A-6-48
G-1 Radio / Allume-cigares ..................... 8A-6-49

Liste des connecteurs ..................................8A-7-1

B Connecteur ............................................8A-7-1
C Connecteur ............................................8A-7-1
D Connecteur ............................................8A-7-2
E Connecteur ............................................8A-7-2
J Connecteur.............................................8A-7-4

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Бренд: Mercedes-Benz Страницы: 373
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Бренд: Cadillac Страницы: 368
Luverne 205760 Installation Instructions preview
205760
Бренд: Luverne Страницы: 3
Navman B2+ User Manual preview
B2+
Бренд: Navman Страницы: 27
Beper P205DIF100 Manual preview
P205DIF100
Бренд: Beper Страницы: 52
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Бренд: Honda Страницы: 22
Mercedes-Benz 2013 CL Operator'S Manual preview
2013 CL
Бренд: Mercedes-Benz Страницы: 494
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Бренд: Roadmaster Страницы: 4
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
Metra Electronics 99-3305 Installation Instructions Manual preview
99-3305
Бренд: Metra Electronics Страницы: 12
Jeep 2012 Patriot Series Owner'S Manual preview
2012 Patriot Series
Бренд: Jeep Страницы: 505
Toyota 2009 Tacoma Quick Reference Manual preview
2009 Tacoma
Бренд: Toyota Страницы: 22
Enduro EM303 User Manual preview
EM303
Бренд: Enduro Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды