manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL INJECTOR

ON-VEHICLE INSPECTION

1) Using sound scope or such, check operating sound of injector

when engine is running or cranking.
Cycle of operating sound should vary according to engine
speed.
If no sound or an unusual sound is heard, go to “B-2 Fuel Injec-
tor Circuit Check” in this section.

2) Disconnect connector from injector, connect ohmmeter be-

tween terminals of injector and check resistance.

Resistance of injector: 10 – 15 

at 20

_

C, 68 

_

F

If resistance is out of specification, replace.

3) Connect connector to injector securely.

REMOVAL

1) Relieve fuel pressure in fuel feed line. Refer to “Fuel Pressure

Relief Procedure” in Section 6.

2) Disconnect battery negative cable at battery.
3) Disconnect connector from each injector.
4) Remove fuel delivery pipe bolts.
5) Remove fuel injector(s) from delivery pipe and intake manifold.

WARNING:
A small amount of fuel may be released when fuel injector
is removed. In order to reduce the chance of personal in-
jury, cover than with a shop cloth.

NOTE:
Confirm fuel pressure before this inspection.

INJECTION VOLUME INSPECTION

WARNING:
As fuel is injected in this inspection, perform in a well
ventilated area and away from open flames.
Use special care to prevent sparking when connecting
and disconnecting test lead to and from battery.

ENGINE AND EMISSION CONTROL SYSTEM

6E-65

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Бренд: UMBRA RIMORCHI Страницы: 18
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Бренд: OCTO Страницы: 5
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Whispbar K611W Fitting Instructions Manual preview
K611W
Бренд: Whispbar Страницы: 77
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Бренд: Metra Electronics Страницы: 20
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Бренд: Mercedes-Benz Страницы: 358
Camecho R0009 Instructions preview
R0009
Бренд: Camecho Страницы: 2
Eibach E60-82-007-02-10 Installation Instructions preview
E60-82-007-02-10
Бренд: Eibach Страницы: 3
KEKO K617 Installation Description preview
K617
Бренд: KEKO Страницы: 3
Movon MDAS-5 Installation Manual preview
MDAS-5
Бренд: Movon Страницы: 43
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Бренд: Lantronix Страницы: 51

Бренды по названию

Популярные бренды

Загрузить еще бренды