manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

LIVE (UNDEPLOYED) AIR BAG (INFLATOR) MODULES

Special care is necessary when handling and storing a live (unde-
ployed) air bag (inflator) modules.
The rapid gas generation produced during deployment of the air
bag could cause the air bag (inflator) module, or an object in front
of the air bag (inflator) module, to be thrown through the air in the
unlikely event of an accidental deployment.

Never attempt disassembly of the air bag (inflator) modules.

If any abnormality is found, be sure to replace it with new one as
an assembly.

When an abnormality is noted as existing in the live (unde-
ployed) air bag (inflator) module, be sure to deploy it before dis-
carding it.

When grease, cleaning agent, oil, water, etc., got on the air bag
(inflator) modules (driver and passenger), wipe it off immediately
with a dry cloth.

If air bag (inflator) module was dropped from a height of 90 cm
(3 ft) or more, it should be replaced with a new one as an assem-
bly.

WARNING:
Never attempt to measure the resistance of the air bag
(inflator) modules (driver and passenger). It is very dan-
gerous as the electric current from the tester may deploy
the air bag.

ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.

WARNING:

For handling and storage of a live air bag (inflator)
module, select a place where the ambient temperature
below 65

C (150

F), without high humidity and away

from electric noise.

When carrying a live air bag (inflator) module, make
sure the bag opening is pointed away from you. In case
of an accidental deployment, the bag will then deploy
with minimal chance of injury. Never carry the air bag
(inflator) module by the wires or connector on the un-
derside of the module.

Otherwise, personal injury may result.

AIR BAG SYSTEM

10B-41

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Бренд: CITROËN Страницы: 301
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Бренд: Whipple Страницы: 3
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
Volvo 164 1969 Service Manual preview
164 1969
Бренд: Volvo Страницы: 266
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Бренд: Gator Страницы: 8
benbat BM721 Instructions For Use Manual preview
BM721
Бренд: benbat Страницы: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Бренд: SPL Страницы: 5
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
cam 40103 AL Mounting Instructions preview
40103 AL
Бренд: cam Страницы: 6
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Бренд: Maserati Страницы: 302
Navman T1 F20 User Manual preview
T1 F20
Бренд: Navman Страницы: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Бренд: Macrom Страницы: 10
Needit Park Mini User Manual preview
Park Mini
Бренд: Needit Страницы: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Бренд: Gemini Страницы: 6
Edelbrock 29135 Installation Instructions preview
29135
Бренд: Edelbrock Страницы: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Бренд: Mercedes-Benz Страницы: 93

Бренды по названию

Популярные бренды

Загрузить еще бренды