manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Below
specified value

6-68

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

DTC DETECTING CONDITION

POSSIBLE CAUSE

D

Engine under other than high revolution condition

D

Not on rough road

D

Engine speed changing rate

D

Manifold absolute

pressure changing rate

D

Throttle opening changing rate

D

Misfire rate per 200 or 1000 engine revolutions (how

much and how often crankshaft revolution speed

changes) is higher than specified value

D

Engine overheating

D

Vacuum leaks (air inhaling) from air intake system

D

Ignition system malfunction (spark plug(s), high-

tension cord(s), ignition coil assembly)

D

Fuel pressure out of specification

D

Fuel injector malfunction (clogged or leakage)

D

Engine compression out of specification

D

Valve lash (clearance) out of specification

D

Manifold absolute pressure sensor malfunction

D

Engine coolant temp. sensor malfunction

D

PCV valve malfunction

D

EVAP control system malfunction

D

EGR system malfunction

DTC CONFIRMATION PROCEDURE
NOTE:
Among different types of random misfire, if misfire occurs at cylinders 1 and 4 or cylinders 3 and 2 simulta-
neously, it may not possible to reconfirm DTC by using the following DTC confirmation procedure. When
diagnosing the trouble of DTC P0300 (Random misfire detected) of the engine which is apparently misfir-
ing, even if DTC P0300 cannot be reconfirmed by using the following DTC confirmation procedure, pro-
ceed to the following Diag. Flow Table.

WARNING:

D

When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.

D

Road test should be carried out with 2 persons, a driver and a tester.

1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:

– Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
– Ambient temp.: – 10

_

C, 14

_

F or higher

– Intake air temp.: 70

_

C, 158

_

F or lower

– Engine coolant temp.: – 10 – 110

C, 14 – 230

F

4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-

sis” and “Freeze frame data check”.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Бренд: ULTIMATE SPEED Страницы: 19
Vauxhall Cascada Quick Reference Manual preview
Cascada
Бренд: Vauxhall Страницы: 2
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Бренд: Kia Страницы: 10
Kuda 182220 Installation Instruction preview
182220
Бренд: Kuda Страницы: 3
Rati Armster 2 User Manual preview
Armster 2
Бренд: Rati Страницы: 2
Quadratec 12057.0261 Installation Manual preview
12057.0261
Бренд: Quadratec Страницы: 12
Hank HKWP1100-10Q User Quick Manual preview
HKWP1100-10Q
Бренд: Hank Страницы: 2
Fab Fours H4550 Installation Instructions Manual preview
H4550
Бренд: Fab Fours Страницы: 13
CrimeStopper CA-504.BRKT Install Manual preview
CA-504.BRKT
Бренд: CrimeStopper Страницы: 1
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
Brodit ProClip 833995 Manual preview
ProClip 833995
Бренд: Brodit Страницы: 2
Chevrolet Chevy II 1965 Owner'S Manual preview
Chevy II 1965
Бренд: Chevrolet Страницы: 46
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
Revelation lnd-10716 Installation Instructions preview
lnd-10716
Бренд: Revelation Страницы: 4
Kia Soul 2018 Owner'S Manual preview
Soul 2018
Бренд: Kia Страницы: 673
Saab 9-3 M03- Installation Instructions Manual preview
9-3 M03-
Бренд: Saab Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды