manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Steering Rack

Inspect for deflection, teeth wear, or damage, back surface wear
or damage.

Limit of rack deflection: 0.35 mm (0.014 in.)

If deflection exceeds limit, replace rack.

CAUTION:
Do not use a wire brush when cleaning.

ASSEMBLY

Install in reverse order of removal, nothing following points.
1) Install pinion bearing oil seal to pinion bearing plug with special

tool.

Special Tool
(C): 09925-98220

2) Apply grease to oil seal lip.

“

A”: Grease 99000-25050

1. Pinion bearing plug

3) Apply grease to entire teeth surface of rack and its periphery.

“

A”: Grease 99000-25050

4) Slide rack into steering gear case in the direction as shown.

CAUTION: 
Inside of steering rack bushing is coated with special
coating. As it is damageable, be very careful not to
cause damage to it when inserting rack into steering
gear case.

1. Rack
2. Steering gear case

5) Apply grease to all around pinion teeth, pinion bearing and gear

case oil seal lip.

“

A”: Grease 99000-25050

1. Gear case oil seal
2. Pinion teeth
3. Fill inside of pinion

bearing plug with
grease.

4. O-ring
5. Pinion bearing plug
6. Pinion bearing

MANUAL RACK AND PINION

3B-7

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Бренд: Jeep Страницы: 608
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Бренд: GMC Страницы: 433
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Бренд: Dometic Страницы: 158
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Бренд: Subaru Страницы: 21
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Бренд: NavLinkz Страницы: 21
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Streetwize SWGH3 Quick Start Manual preview
SWGH3
Бренд: Streetwize Страницы: 4
Yakima K974 Manual preview
K974
Бренд: Yakima Страницы: 11
Toyota 2011 Camry SE V6 Brochure & Specs preview
2011 Camry SE V6
Бренд: Toyota Страницы: 33
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Бренд: Coolster Страницы: 45
DRAGONFIRE 11-0800 Installation Instructions preview
11-0800
Бренд: DRAGONFIRE Страницы: 4
Chevrolet 1995 C/K Pickup Owner'S Manual preview
1995 C/K Pickup
Бренд: Chevrolet Страницы: 483
HOLDEN Malibu EM 2015 Owner'S Handbook Manual preview
Malibu EM 2015
Бренд: HOLDEN Страницы: 330
Alfa Romeo Stelvio 2019 User Manual preview
Stelvio 2019
Бренд: Alfa Romeo Страницы: 268
ADAPT SOLUTIONS ASENTO EV-EXP18R Installation Manual preview
ASENTO EV-EXP18R
Бренд: ADAPT SOLUTIONS Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды