PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT
When Immobilizer Control Module was replaced, including when
replaced because rechecking by using a known-good Immobilizer
Control Module was necessary during trouble diagnosis, register
Transponder code and ECM/Immobilizer Control Module code in
Immobilizer Control Module and ECM/Immobilizer Control Module
code in ECM by performing following procedure.
1) Perform steps 1) and 2) described in “How To Register Ignition
Key”.
2) Prepare ignition key with a built-in transponder. And then turn
ignition switch ON by using it.
3) Using SUZUKI scan tool, clear all transponder codes registered
in Immobilizer Control Module by executing “CLR. TRANS COD
(CLEAR TP CODE)” command in SELECT MODE menu.
NOTE:
When “CLR. TRANS COD (CLEAR TP CODE)” command is
executed with the malfunction indicator lamp (if not
equipped with immobilizer indicator lamp) ON or the immo-
bilizer indicator lamp ON, it remains ON even after execu-
tion of that command is over. It will start flashing when the
ignition switch is turned OFF once and then turned ON after
some seconds.
4) Using SUZUKI scan tool, register Transponder code in Immobi-
lizer Control Module by executing “ENT. TRANS COD (ENT. TP
CODE)” command in SELECT MODE menu.
5) Using SUZUKI scan tool, register ECM/Immobilizer Control
Module code in both Immobilizer Control Module and ECM by
executing “RECORD ECU (RECORD ECM/PCM/ICM)” com-
mand in SELECT MODE menu.
6) Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
7) If any other Transponder code for ignition key with a built-in
transponder needs to be registered, repeat above steps 2), 4)
and 6).
NOTE:
Up to 4 Transponder codes for ignition key with a built-in
transponder can be registered.
It is not possible to register the same Transponder code
for ignition key with a built-in transponder as the one al-
ready registered in Immobilizer Control Module.
8G-26
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
GA413
supple
Содержание GA413
