manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

9) Connect parking brake cable to brake back plate and install

brake shoe and brake drum, refer to PARKING BRAKE
CABLE INSTALLATION of Section 5.

10) Refill rear axle (differential) housing with new specified gear

oil. Refer to Section 7F for refill.

11) Fill reservoir with brake fluid and bleed brake system.

(For bleeding operation, see Section 5.)

12) Install wheel and tighten wheel nuts to specified torque.
13) Upon completion of all jobs, detach plug from brake back plate

and turn adjuster upward by flat head screw driver and de-
press brake pedal with about 30 kg (66 lbs) load three to five
times so as to obtain proper drum-to-shoe clearance.
Adjust parking brake cable (for adjustment, see Section 5 of
this manual).

14) Check to ensure that brake drum is free from dragging and

proper braking is obtained.

15) Perform brake test (foot brake and parking brake).

(For brake test, see Section 5).

16) Check each installed part for oil leakage.

REAR AXLE SHAFT INNER OIL SEAL

REMOVAL
1) Remove rear axle shaft. For details, refer to steps 1) to 7) of

REAR AXLE SHAFT REMOVAL in this section.

2) Remove rear axle shaft inner oil seal, by using special tools.

Special Tool
(E): 09942-15510
(F): 09944-96010 (remover)
(G): 09921-26010 (collar)

INSTALLATION
1) Using special tools drive in oil seal until it contacts oil seal pro-

tector in axle housing.

NOTE:

Make sure that oil seal is free from inclination as it is
installed.

Refer to figure so that oil seal is installed in proper direc-
tion.

Special Tool
(H): 09913-75520

“A”: Grease 99000-25010

2) For procedure hereafter, refer to steps 4) to 16) of REAR AXLE

SHAFT INSTALLATION in this section.

1. Inner oil seal
2. Oil seal protector
3. Differential side

3E-16

REAR SUSPENSION

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Бренд: hager Страницы: 9
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
Alfa Romeo 1966 Spider 105 Faq preview
1966 Spider 105
Бренд: Alfa Romeo Страницы: 46
Aries 205039 Installation Manual preview
205039
Бренд: Aries Страницы: 5
Mercedes-Benz MY17 c-class Operator'S Manual preview
MY17 c-class
Бренд: Mercedes-Benz Страницы: 354
Fab Fours C3150 Installation Instructions Manual preview
C3150
Бренд: Fab Fours Страницы: 21
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Бренд: Honda Страницы: 22
Mercedes-Benz 2013 CL Operator'S Manual preview
2013 CL
Бренд: Mercedes-Benz Страницы: 494
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Бренд: PEUGEOT Страницы: 232
INNO TR163 Installation Instructions preview
TR163
Бренд: INNO Страницы: 3
Adaptiv Mini CAM-MB6-AD User Manual preview
CAM-MB6-AD
Бренд: Adaptiv Mini Страницы: 4
GEMINI TECHNOLOGY 514F User Manual preview
514F
Бренд: GEMINI TECHNOLOGY Страницы: 9
PEUGEOT 208 T16 User Manual preview
208 T16
Бренд: PEUGEOT Страницы: 67
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Бренд: Quadratec Страницы: 20
TRAMEC CV 1 Series Manual preview
CV 1 Series
Бренд: TRAMEC Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды