manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL DELIVERY SYSTEM

FUEL PRESSURE INSPECTION

1) Relieve fuel pressure in fuel feed line referring to “Fuel Pressure

Relief Procedure” in Section 6.

WARNING:
Be sure to perform work in a well-ventilated area and
away from any open flames, or there is a risk of a fire
breaking out.

2) Disconnect fuel feed hose from fuel delivery pipe.

3) Connect special tools and hose between fuel delivery pipe and

fuel feed hose as shown in figure, and clamp hoses securely to
ensure no leaks occur during checking.

Special Tool
(A): 09912-58441
(B): 09912-58431
(C): 09912-58490

4) Check that battery voltage is above 11 V.

CAUTION:
A small amount of fuel may be released when fuel
hose is disconnected. Place container under the joint
with a shop cloth so that released fuel is caught in
container or absorbed in cloth. Place that cloth in an
approved container.

270 – 310 kPa

2.7 – 3.1 kg/cm

2

38.4 – 44.0 psi

At specified idle
speed

With 1 min. after 
engine (fuel pump)
stop (Pressure re-
duces as time passes)

over 250 kPa

2.5 kg/cm

2

35.6 psi

CONDITION

FUEL PRESSURE

With fuel pump 
operating and engine
stopped

5) Turn ignition switch ON to operate fuel pump and after 2 se-

conds turn it OFF. Repeat this 3 or 4 times and then check fuel
pressure.

6) Start engine and warm it up to normal operating temperature.
7) Measure fuel pressure at idling.

If measured pressure doesn’t satisfy specification, refer to
“Diagnostic Flow Table B-3” in “Engine Diagnosis” section and
check each possibly defective part. Replace if found defective.

210 – 260 kPa

2.1 – 2.6 kg/cm

2

29.8 – 37.0 psi

8) After checking fuel pressure, remove fuel pressure gauge.

CAUTION:
As fuel feed line is still under high fuel pressure, make
sure to release fuel pressure according to following
procedures.

Place fuel container under joint.

Cover joint with rag and loosen joint nut slowly to
release fuel pressure gradually.

ENGINE AND EMISSION CONTROL SYSTEM

6E-19

GA413
supple

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 94
Camoplast T4S User Manual preview
T4S
Бренд: Camoplast Страницы: 60
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Бренд: Kolpin Страницы: 25
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Бренд: IBASE Technology Страницы: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Бренд: Modifry Products Страницы: 2
TATA Motors tigor Owner'S Manual preview
tigor
Бренд: TATA Motors Страницы: 159
Alfa Romeo Alfa 147 Quick Start Manual preview
Alfa 147
Бренд: Alfa Romeo Страницы: 8
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
Toro 137-1019 Installation Instructions Manual preview
137-1019
Бренд: Toro Страницы: 24
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Бренд: Veigel Страницы: 24
Cellular Line interphone Instruction Manual preview
interphone
Бренд: Cellular Line Страницы: 25
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
Great Wall WEY VV5 Service Manual preview
WEY VV5
Бренд: Great Wall Страницы: 18
WIX WP9378 Installation Instruction preview
WP9378
Бренд: WIX Страницы: 2
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды