manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL TANK

REMOVAL

WARNING:
Refer to the WARNING at the beginning of ON-VEHICLE
SERVICE in this section.

1) Relieve fuel pressure in fuel feed line referring to “ENGINE”

section.

2) Disconnect negative cable at battery.

3) Hoist vehicle.
4) Disconnect fuel pump wire coupler.

1. Fuel pump wire coupler

2. Fuel tank

6) Disconnect fuel filler hose from filler neck, breather hose from

tank.

1. Fuel filler hose
2. Breather hose
3. Fuel filler neck
4. Fuel tank

5) Due to absence of fuel tank drain plug, drain fuel tank by pump-

ing fuel out through fuel tank filler.
Use hand operated pump device to drain fuel in space “A” in the
figure.

CAUTION:
Never drain or store fuel in an open container due to
possibility of fire or explosion.

1. Fuel filler hose
2. Fuel tank inlet (check) valve

ENGINE FUEL

6C-7

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Yakima SkyBox 12 Installation Instructions Manual preview
SkyBox 12
Бренд: Yakima Страницы: 6
Yakima HoldUp Plus2 Manual preview
HoldUp Plus2
Бренд: Yakima Страницы: 18
IAG IAG-ENG-5003BK Instructions preview
IAG-ENG-5003BK
Бренд: IAG Страницы: 3
Alpine eX-10 Owner'S Manual preview
eX-10
Бренд: Alpine Страницы: 69
Allen Sports S302 Instructions preview
S302
Бренд: Allen Sports Страницы: 2
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
Condor T-RAMP Quick Start Manual preview
T-RAMP
Бренд: Condor Страницы: 2
iArmor EDGE IA-N098 Quick Start Manual preview
EDGE IA-N098
Бренд: iArmor Страницы: 4
ideus VV950 User Manual preview
VV950
Бренд: ideus Страницы: 159
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Бренд: Mazda Страницы: 122
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Бренд: Skoda Страницы: 16
LXE Akerstroms Tx700 Configuration Manual preview
Akerstroms Tx700
Бренд: LXE Страницы: 146
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Бренд: Oldsmobile Страницы: 354
Volvo 30661683 Installation Instructions, Accessories preview
30661683
Бренд: Volvo Страницы: 18
Whispbar WB201 Manual preview
WB201
Бренд: Whispbar Страницы: 14
Car-Interface CI-RL4-R40 Manual preview
CI-RL4-R40
Бренд: Car-Interface Страницы: 25
Wald Black Bison Sports Series Installation Manual preview
Black Bison Sports Series
Бренд: Wald Страницы: 7
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Бренд: Quadratec Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды