manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

CRANKSHAFT POSITION SENSOR (CKP
SENSOR)

ON-VEHICLE INSPECTION

1) Disconnect negative cable at battery.
2) Disconnect connector from CKP sensor.
3) Measure resistance between each terminal of CKP sensor.

Resistance: 360 – 460

 at 20

C (68

F)

4) Measure resistance between each terminal and ground.

Resistance: 1M

 or more

5) If resistance is out of specification, replace.

REMOVAL

1) Disconnect negative cable at battery.
2) Disconnect connector from CKP sensor.
3) Remove CKP sensor from oil pan.

INSTALLATION

1) Check that CKP sensor is free from any metal particles.
2) Install CKP sensor to oil pan.

Tightening Torque
(a): 10 N

.

m (1.0 kg-m)

3) Connect connector to CKP sensor.

CAUTION:
Be sure to tighten to specified torque. CKP sensor will
be deformed if overtightened and correct CKP sensor
signal will not be fed if loosened.

1. CKP sensor

CKP SENSING ROTOR

INSPECTION

1) Remove timing belt cover.
2) Check CKP sensing rotor for damage.
3) If found faulty, replace any defective parts.

1. CKP sensing rotor
2. CKP sensor

ENGINE AND EMISSION CONTROL SYSTEM

6E-73

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Бренд: Mazda Страницы: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Бренд: Cadillac Страницы: 496
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Бренд: VDO Страницы: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Бренд: Wagan Страницы: 3
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Бренд: T-Mobile Страницы: 2
AIS MAZMOD2 Manual preview
MAZMOD2
Бренд: AIS Страницы: 2
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Бренд: SilverLeaf Electronics Страницы: 16
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Бренд: Maserati Страницы: 302
JAC HFC7151M1V-U221B Workshop Manual preview
HFC7151M1V-U221B
Бренд: JAC Страницы: 106
Blackhawk Automotive BH6010 Operating Instructions And Parts Manual preview
BH6010
Бренд: Blackhawk Automotive Страницы: 8
UCANDAS VDM Instruction Of Quick Operation preview
VDM
Бренд: UCANDAS Страницы: 4
HAUL MASTER 96198 Instructions preview
96198
Бренд: HAUL MASTER Страницы: 4
Funkwerk EGO FLASH Operating Manual preview
EGO FLASH
Бренд: Funkwerk Страницы: 58
Honda 2012 Odyssey Owner'S Manual preview
2012 Odyssey
Бренд: Honda Страницы: 441

Бренды по названию

Популярные бренды

Загрузить еще бренды