manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

INSPECTION

Using a straight edge and thickness gauge, check surface at a
total of 6 locations. If distortion limit, given below, is exceeded,
correct gasketed surface or replace intake manifold.

Limit of distortion: 0.07 mm (0.003 in.)

INSTALLATION

Reverse removal procedure for installation noting the followings.

Use new intake manifold gasket.

Tighten bolts and nuts to specified torque.

Tightening Torque
(a): 23 N·m (2.3 kg-m, 17.0 lb-ft)
(b): 50 N·m (5.0 kg-m, 36.5 lb-ft)

Connect gear shift cables to gear shift control lever, refer to
GEAR SHIFT CONTROL INSTALLATION in Section 7A.

Connect parking brake cable to parking brake lever and perform
parking brake adjustment by referring PARKING BRAKE IN-
SPECTION AND ADJUSTMENT in Section 5.

Adjust accelerator cable play, referring to Section 6E.

Check to ensure that all removed parts are back in place. Rein-
stall any necessary parts which have not been reinstalled.

Install engine room center member.

Refill cooling system and bleed air from system, referring to Sec-
tion 6B.

Adjust generator drive belt tension, referring to BELT TENSION
INSPECTION in Section 6H.

Upon completion of installation, turn ignition switch ON but en-
gine OFF and check for fuel leaks.

Finally, start engine and check for engine coolant leaks.

ENGINE MECHANICAL

6A-13

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Бренд: Federal Signal Corporation Страницы: 13
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Бренд: Eaton Страницы: 12
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
KEKO K617 Installation Description preview
K617
Бренд: KEKO Страницы: 3
Movon MDAS-5 Installation Manual preview
MDAS-5
Бренд: Movon Страницы: 43
Bestop 614.04 Installation Manual preview
614.04
Бренд: Bestop Страницы: 31
PEUGEOT 108 2017 Vehicle Instruction Card preview
108 2017
Бренд: PEUGEOT Страницы: 17
rough country 921107830 Installation Instruction preview
921107830
Бренд: rough country Страницы: 4
Acura RLX 2016 Service Bulletin preview
RLX 2016
Бренд: Acura Страницы: 7
Phonocar VM 320 Instruction Manual preview
VM 320
Бренд: Phonocar Страницы: 28
ROLEC WallPod Series Installation Instructions preview
WallPod Series
Бренд: ROLEC Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды