manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ENGINE GENERAL INFORMATION AND DIAGNOSIS

6-83

GA413
supple

DTC P0480

INSPECTION

STEP

ACTION

YES

NO

1

Was “ENGINE DIAG. FLOW TABLE” performed?

Go to Step 2.

Go to “ENGINE DIAG.
FLOW TABLE”.

2

1) With ignition switch OFF position, install SUZU-

KI scan tool.

2) Start engine and run it at idle.
3) Observe engine coolant temperature on scan

tool.

Does cooling fan turn ON when engine coolant

temperature reaches above 90

C (194

F)?

Radiator fan control sys-

tem is functioning nor-

mally.

Go to Step3.

3

1) Stop engine.
2) With ignition switch OFF position, disconnect

radiator fan relay.

3) Inspect radiator fan relay. Refer to “Main Relay/

Fuel Pump Relay/Radiator Fan Relay Inspec-
tion” in Section 6E.

Is radiator fan relay functioning normally?

Go to Step 4.

Faulty radiator fan relay.

4

1) Turn ignition switch ON position, leaving engine

OFF.

2) Measure voltage from “a” of radiator fan relay

connector to ground, from “c” of radiator fan
relay connector to ground. See Fig.1.

Is each voltage within 10-14V?

Go to Step 5.

Faulty “BLU/WHT”, 

“BLK/RED” wire.

5

1) Turn ignition switch OFF position.
2) Connect jumper wire between “a” and “b” of

radiator fan relay connector. See Fig.2.

Does cooling fan turn ON when ignition switch

turns ON position, leaving engine OFF?

Faulty “RED/GRN” wire.

If wire and connection

are OK, substitute a

known-good ECM and

recheck.

Faulty “BLU/RED”,

“BLK” wire.

Faulty radiator fan mo-

tor.

Poor connection.

Fig. 1 for Step 4

Fig. 2 for Step 5

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Vauxhall Cascada Quick Reference Manual preview
Cascada
Бренд: Vauxhall Страницы: 2
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Бренд: GMC Страницы: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Бренд: Prorack Страницы: 15
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Бренд: Axxess Страницы: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Бренд: SeaSucker Страницы: 9
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Бренд: K&M Страницы: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Бренд: Car-Interface Страницы: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Бренд: Thule Страницы: 6
Thule CIRCUIT 526XT Manual preview
CIRCUIT 526XT
Бренд: Thule Страницы: 12
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
EUFAB 16458 Operating Instructions Manual preview
16458
Бренд: EUFAB Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды