manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ON-VEHICLE SERVICE

ACCELERATOR CABLE ADJUSTMENT

1) With throttle valve closed, check accelerator pedal play which

should be within following specification.

Pedal play “a”: 2 – 7 mm (0.08 – 0.27 in.)

If measured value is out of specification, adjust it to specification
with cable adjusting nut (2).

1. Accelerator cable
2. Adjusting nut
3. Lock nut

2) With accelerator pedal depressed fully, check clearance be-

tween throttle lever (2) and lever stopper (1) (throttle body)
which should be within following specification.

Clearance “a” : 0.5 – 2.0 mm (0.02 – 0.07 in.)
(With pedal depressed fully)

If measured value is out of specification, adjust it to specification
by changing height of pedal stopper bolt (3).

IDLE SPEED/IDLE AIR CONTROL (IAC)
DUTY INSPECTION

Before idle speed / IAC duty check, make sure of the following.

Lead wires and hoses of Electronic Fuel Injection and engine
emission control systems are connected securely.

Accelerator cable has some play, that is, it is not tight.

Valve lash is checked and adjusted according to maintenance
schedule.

Ignition timing is within specification.

All accessories (wipers, heater, lights, A / C, etc.) are out of ser-
vice.

Air cleaner has been properly installed and is in good condition.

No abnormal air inhaling from air intake system.

After above items are all confirmed, check idle speed and IAC duty
as follows.
NOTE:
Before starting engine, place transmission gear shift lever in
“Neutral” and set parking brake and block drive wheels.

6E-12

ENGINE AND EMISSION CONTROL SYSTEM

GA413
supple

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
Ignition 63-231 Quick Start preview
63-231
Бренд: Ignition Страницы: 1
KAP AUDI 4G HIGHEND Manual preview
AUDI 4G HIGHEND
Бренд: KAP Страницы: 20
GARO ENTITY PRO Installation preview
ENTITY PRO
Бренд: GARO Страницы: 2
Marlon Xplore Pro II SxS Owner’S Manual Assembly & Installation Instructions preview
Xplore Pro II SxS
Бренд: Marlon Страницы: 15
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Бренд: Honda Страницы: 85
Menabo JUZA Fitting Instructions Manual preview
JUZA
Бренд: Menabo Страницы: 12
Bestop 614.04 Installation Manual preview
614.04
Бренд: Bestop Страницы: 31
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
Mitsubishi 2015 OUTLANDER Owner'S Manual preview
2015 OUTLANDER
Бренд: Mitsubishi Страницы: 490
Porsche 92854 Owner'S Manual preview
92854
Бренд: Porsche Страницы: 145
Safe Fleet RVS-218629 Instruction Manual preview
RVS-218629
Бренд: Safe Fleet Страницы: 28
Buick 1998 Century Owner'S Manual preview
1998 Century
Бренд: Buick Страницы: 372
Jotto Desk Force 475-0750 Installation Instructions preview
Force 475-0750
Бренд: Jotto Desk Страницы: 3
Van Guard IN8377 Fitting Instructions Manual preview
IN8377
Бренд: Van Guard Страницы: 12
QUIK CORP RFBAQ Isuzu FTS 139-260 Manual preview
RFBAQ Isuzu FTS 139-260
Бренд: QUIK CORP Страницы: 132
SSANGYONG 2010 Kyron User Manual preview
2010 Kyron
Бренд: SSANGYONG Страницы: 312
Toyota PK3B1-34H5H Installation Instructions Manual preview
PK3B1-34H5H
Бренд: Toyota Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды