manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

1. Joint
2. Fuel return hose
3. Fuel feed hose
4. Fuel vapor hose
   1: Before disconnecting, blow off dust, etc. of this

portion with compressed air.

11) Disconnect fuel feed hose, fuel vapor hose and fuel return

hose from fuel pump assembly.
When disconnecting joint of fuel feed line or return line from
pipe, unlock joint by inserting special tool between pipe and
joint lock first.

Special Tool
(A): 09919-47020

Disconnect joint from pipe.

WARNING:
A small amount of fuel may be released after the fuel
hose is disconnected. In order to reduce the chance
of personal injury, cover the hose and pipe to be dis-
connected with a shop cloth. Be sure to put that cloth
in an approved container when disconnection is
completed.

INSPECTION

After removing fuel tank, check hoses and pipes connected to fuel
tank for leaks, loose connections, deterioration or damage. Also
check fuel pump assembly gaskets for leaks, visually inspect fuel
tank for leaks and damage.
Replace any damaged or malconditioned parts.

Fuel Tank Purging Procedure

WARNING:
This purging procedure will NOT remove all fuel vapor.
Do not attempt any repair on tank using heat of flame as
an explosion resulting in personal injury could occur.

CAUTION:
Never remain water in fuel tank after washing, or fuel
tank inside will get corrosion.

Following procedure is used purging fuel tank.
1) After removing fuel tank, remove all hoses, pipes, fuel pump as-

sembly from fuel tank.

2) Drain all remaining fuel from tank.
3) Move tank to flushing area.
4) Fill tank with warm water or tap water, and agitate vigorously

and drain. Repeat this washing until inside of tank is clean.
Replace tank if its inside is rusty.

5) Completely flush out remaining water after washing.

ENGINE FUEL

6C-9

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Бренд: FORM FIT Страницы: 2
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Бренд: Wilco Offroad Страницы: 4
AddSecure Asset Light Installation Manual preview
Asset Light
Бренд: AddSecure Страницы: 14
Cadillac 2003 Seville Owner'S Manual preview
2003 Seville
Бренд: Cadillac Страницы: 402
Cobra BAK R294 Manual preview
BAK R294
Бренд: Cobra Страницы: 2
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Бренд: Safe Fleet Страницы: 12
Oldsmobile Bravada 1997 Owner'S Manual preview
Bravada 1997
Бренд: Oldsmobile Страницы: 358
Curt Manufacturing 58963 Installation Manual preview
58963
Бренд: Curt Manufacturing Страницы: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Бренд: Whispbar Страницы: 112
Safe Fleet PRIME DESIGN HRR3-E-PM52 Manual preview
PRIME DESIGN HRR3-E-PM52
Бренд: Safe Fleet Страницы: 12
Honda Fit LX 2015 Manual preview
Fit LX 2015
Бренд: Honda Страницы: 4
Pet Gear PG9300DR Instruction Manual preview
PG9300DR
Бренд: Pet Gear Страницы: 4
Westin 32-2250 Instructions preview
32-2250
Бренд: Westin Страницы: 3
Xforce PR-104 User Manual preview
PR-104
Бренд: Xforce Страницы: 11
Metra Electronics 95-7617B Installation Instructions Manual preview
95-7617B
Бренд: Metra Electronics Страницы: 8
Nugent Tipper Remote Kit User Manual preview
Tipper Remote Kit
Бренд: Nugent Страницы: 21
Edelbrock 3824 Installation Instructions preview
3824
Бренд: Edelbrock Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды