manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

12) Tighten new armature plate nut as specified below.

Tightening Torque
(a): 14 N

.

m (1.4 kg-m, 10.5 lb-ft)

Special Tool
(A): 09991-06060

1. Armature plate
2. Screw
3. Washer

When replacing other part

REPLENISHING COMPRESSOR OIL

When replacing air conditioning parts with new ones, it is neces-
sary to replenish oil by the amount supposedly remaining in each
part.

When changing gas only

When it is unavoidable to change gas without replacing any com-
ponent part for engine removal and installation or for some other
reason, replenish 100cc oil. When replenishing gas only, oil replen-
ishment is not necessary.

When replacing compressor

Compressor oil is sealed in each new compressor by the amount
required for air conditioner cycle. Therefore, when using a new
compressor for replacement, drain oil from it by the amount calcu-
lated as follows.

“C” = “D” – “E”
“C”: Amount of oil to be drained
“D”: Amount of oil sealed in a new compressor “A”
“E”: Amount of oil remaining in removed compressor “B”

1. New compressor
2. Removed compressor
3. Excess oil (A–B)

1B-18

AIR CONDITIONING

Part replaced

Amount of compressor

oil to be replenished

Evaporator

25 cc

Condenser

15 cc

Receiver/dryer

20 cc

Hoses

10 cc each

Pipes

10 cc each

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Yakima Q46 Installation Instructions preview
Q46
Бренд: Yakima Страницы: 4
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Бренд: FABBRI PORTATUTTO Страницы: 2
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Бренд: Genesis Страницы: 3
Audi A4 2016 Quick Questions And Answers preview
A4 2016
Бренд: Audi Страницы: 9
Belkin WIC004 Setting Up preview
WIC004
Бренд: Belkin Страницы: 4
Parkeon StradaPAL Installation Manual preview
StradaPAL
Бренд: Parkeon Страницы: 43
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Бренд: PAC Страницы: 14
Kolpin 98310 Product Instructions preview
98310
Бренд: Kolpin Страницы: 3
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Бренд: Subaru Страницы: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Бренд: Subaru Страницы: 328
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
Camoplast T4S Installation Manuallines preview
T4S
Бренд: Camoplast Страницы: 19
Prorack K577W Fitting Instructions Manual preview
K577W
Бренд: Prorack Страницы: 15
Volvo 30795637 User Manual preview
30795637
Бренд: Volvo Страницы: 92
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Бренд: Butts of Bawtry Страницы: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Бренд: Belkin Страницы: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Бренд: Rover Страницы: 285
Xpresskit 20110601 Installation Manual preview
20110601
Бренд: Xpresskit Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды