manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

AIR INTAKE SYSTEM

THROTTLE BODY

ON-VEHICLE INSPECTION

Check that throttle valve lever moves smoothly.

REMOVAL

1) Disconnect negative cable at battery.
2) Drain cooling system. Refer to section 6B.
3) Disconnect accelerator cable from throttle body.
4) Disconnect electric connectors from TP sensor, MAP sensor

and IAC valve.

5) Disconnect air cleaner outlet hose and coolant hoses from

throttle body.

6) Remove throttle body from intake manifold.

CAUTION:
TP sensor, MAP sensor, idle air control valve or other
components containing rubber must not be places in a
solvent or cleaner bath.
A chemical reaction will cause these parts to swell, hard-
en or get distorted.

1. Throttle body
2. Accelerator cable

bracket

3. MAP sensor

4. TP sensor
5. IAC valve
6. Coolant hoses
7. Gasket

INSTALLATION

1) Clean mating surfaces and install throttle body gasket to intake

manifold.
Use new gasket.

2) Install throttle body and accelerator cable bracket to intake

manifold and tighten bolts and nuts to specified torque.

3) Connect coolant hoses to throttle body.
4) Connect connectors to TP sensor, MAP sensor and IAC valve

securely.

5) Install air cleaner outlet hose.
6) Connect accelerator cable and adjust cable play to specifica-

tion. Refer to “Accelerator Cable Adjustment” in this section.

7) Refill cooling system. Refer to section 6B.
8) Connect negative cable at battery.

ENGINE AND EMISSION CONTROL SYSTEM

6E-59

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604
Airstream 2008 Safari Owner'S Manual preview
2008 Safari
Бренд: Airstream Страницы: 103
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Бренд: Audi Страницы: 9
Axxess AXDSPX-TY3 Installation Instructions Manual preview
AXDSPX-TY3
Бренд: Axxess Страницы: 16
Yakima FreshSesh PowderHound Manual preview
FreshSesh PowderHound
Бренд: Yakima Страницы: 18
N2MB Racing WOT Box Installation Instructions Manual preview
WOT Box
Бренд: N2MB Racing Страницы: 13
Pinnacle EPL7SAM+C Series Quick Start Manual preview
EPL7SAM+C Series
Бренд: Pinnacle Страницы: 2
P-Charge STAND-ALONE Operating Instructions Manual preview
STAND-ALONE
Бренд: P-Charge Страницы: 16
Whispbar K665 Manual preview
K665
Бренд: Whispbar Страницы: 31
Erde ST1272A Assembly Instructions preview
ST1272A
Бренд: Erde Страницы: 3
Lippert Components X-Trek Installation Manual preview
X-Trek
Бренд: Lippert Components Страницы: 14
Mitsubishi Electric 1992 Eclipse Service Manual preview
1992 Eclipse
Бренд: Mitsubishi Electric Страницы: 172
Pioneer 12.301038-01 Installation Manual preview
12.301038-01
Бренд: Pioneer Страницы: 2
Jeep 2002 WG Grand Cherokee Service Manual preview
2002 WG Grand Cherokee
Бренд: Jeep Страницы: 10
Metra Electronics JP-RGBKT-1 Manual preview
JP-RGBKT-1
Бренд: Metra Electronics Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды